Automatic generator start and stop / Automatic Transfer Switch / Automatic changeover switch

10q so much for taking time do this lecture and took time to upload it

Too difficult to follow . Need to slow down a bit !

Thanks sir, please can i see how the start and stop connection is done physically, with stop and start button.
I will be grateful if granted.
Thanks

great work ,which software have you used

I love you 😘 great work and very helpful diagram video sooo thanks.............

Hello, where do we get the neutral for the load from? How do we ensure there is always a neutral cable from both supplies without them interconnecting?

Are you doing relay switch for video

OK but I have a question how would this design change if you you wanted to build an ATS that changes between 3 sources. An example would be if you had grid, solar backup and generator in that priority order. Would be great to know as there's almost no info available on this specific topic

Very interesting & really appreciated

Good.. nice thank you

Please sir, the relays and timers for the gen auto start are they DC or AC?

After that how does the generator start if the grid is out.

nice

all ok.
When my grid off then 3 hours Later generator start.
How to set the time

Thank you so much, sir! A very good quality video! Much appreciated!

Thanks for the lessons, please can I apply this to a single Phase? And can I have the circuit diagram for this video, thanks
Thanks in anticipation

Thanks for the lessons, please can I apply this to a single Phase? And can I have the circuit diagram for this video, thanks

Pl show timer s T1 T2 in video with colour animation. Thanks again for video,👌👌👌👌👌

Is this diagram can be in actual wiring of the ats panel?

Thanks for the video, but please can I see its physical build-up

On the grid side you used two timer relays
Can’t one timer relay do the job

Well done sir, pls how will one connect the ats for single phase generator to auto start/stop

شكرا لك أخي الكريم على هذا الفيديو المهم استمر بالعطاء
يا حبذا لو تعمل لنا فيديو اخر عن كيفيه اداره ATS ثلاث مراحل كهرباء الدولة الحكومية وكذالك كهرباء الاشتراك في الحارة وكهرباء مولد البيت في الداخل كيف الىبط بينهما

Thank you sir

A well explained information supported with clear pictorial diagram. Thank you for dedicating your time and effort to share your knowledge on this particular topic. Thank you...much appreciated

great lectures credible and amazing. any chance of scholarships on electrical and electronic engineering into your reputable and renowned Electro Academy..

Thanks sir

Que buen tutorial ... Lo malo es que no se hablar ingles 🤦‍♂️...

Great Sir, Do you have 3 power source ATS model

No entiendo el inglés.

Hey sir what type of timer relay used. Is all the timer relay ON DELAY?

Very clear and understanding

wow nice very very usefull video thank you

So excellent video about automation..


Thanks for like this video from Bangladesh

Thanks a lot
It's very useful 👍💕

Good explanation

Very good.thank you sir

This design is suitable for Single Phase Gride and Single Phase Generator?
and how many self start attempt?

Please if am to design this ATS for a load wattage of 25,000watts in facility what is the the size of panel by millimeters I should request to buy? That would contain these components

This was an explanation thank you Sir please what are components that make up this design and connection? I know 2 magnetic contactor, 1 phase failure relay, 3 Double pole double throw 8 relay, 2 AC double pole breaker, 5 Timers
Secondly on the battery relays you connected port 1 and 3 of start and port 1 and 3 of stop to what components is it 1 and 2 start- push and 3 and 4 stop-push components?

Can you explain how connect swich of generator to run and stop generator auto. Please draw wiring diagram for connections

Very Nice . Can we have a ladder diagram of the ATS explained above?

Can we common all the neutral...??

A very good tutorial 👌

How to emergence stop button. Sir..

Please explain how Manual and Auto mode is achieved in ATS

The best tutorial..

Very nice and vivid current flow is illustrated. Makes everything clear how does it work. And explained simple. Much of thanks to u !

make the video two pump controlled by latching relay plz