DJI O3 FPV What Goggles Are Compatible & FPV.WTF OSD?

I update the 1.040000 but keep the 606 firmware. Then i put the hack again o3 unit option disappear. I just have DJI FPV option. Still bind to o3 air unit or WTFOS hack is not compatible with o3 air unit? Thanks!

No thanks, you need to activate the Goggles and Camera with DJI. If you don't want privacy, then buy it.

There is a full downgrade option now with WTF Butter! So any version can be downgraded, rooted and upgraded!

Hi Mad Tech, do you know what is the equivalent in EmuFlight for these BF parameters? I have quad using emuflight and I need the OSD in my dji goggles 2

* set osd_displayport_device = MSP

* set displayport_msp_serial = 4

I have few drones with vista units and 1 new DJI 03 unit. When I switch between modes on the v2 goggles I have to rebind either the 03 unit or the vista😡 Am I doing something wrong or is this a common problem??

is it possible to v1 board can swap a v2 internal or to fit a v2 board.?

I purchased a set of refurbished V2 goggles specifically to use with the air unit. I didn't want DJI's latest firmware infecting my V2 goggles I use for Vista units or have the Vista units infected by DJI's latest control grab firmware. The refurbished goggles are now set up with the 03 air unit. I used the Assistant 2 (FPV series) and the Assistant 2 (consumer drone series) to update, however, even though both assistant 2 versions showed the goggles were activated and updated to the latest firmware versions (screen blocked with message "firmware not the latest version, connect to fly app and update to the latest firmware) I could not get a settings screen until I connected to the fly app. I did the fly app last, I did not have to bind the DJI FPV quad and after the fly app update I did have the settings screen needed to switch to 03 air unit mode. Note: The goggles were refurbished and had to be set up like "new" goggles.

Thanks for the thorough review! Could you share what your spectrum analyzer setup is?

Muito bom

V2's let you also use and analog module so you can tinywhoop too without another set of goggles!

Great video. Answers the questions I had on running my V2 goggles with the 03 unit

Is it possible to go further than 13.3km with the o3 and v2 goggles?

is the goggle 2 compatible with DJI FPV?

does it work with the old remote?

So my goggle v2 are rooted so I can update use O3 and still use my Vista and air unit with wtfos

Thanks so much for this explanation :)

If I upgrade the V2 firmware for the o3 will I still be compatible with my old o2 air units?

Dji goggles v1 support on Dji O3 Air unite?

So if I upgrade my v2 rooted goggles to the newest version I wouldn't be able to connect to the Vista kit, right?

Hi , the big problem now at this days , if you switch vista to o3 air unit: we must REBIND every Time :(

Hi , I have rooted my V2 goggles with WTFOS and worked properly, after i update to be compatible with O3 air unit , now I don't have wtfos OSD with my vista and old air unit , am I missing something?

i wonder if you could flash the v1 goggles with the v2 firmware and trick the 03 unit into compatibility

So if i have DJI FPV Goggles V2 and there on firmware v01.02.0015. Can it be rooted for the Custom FPV-WTF OSD? Does it need to be downgraded first? They haven't been updated since early '22..

Hi. Just a silly question. If I bind my V2 goggles to a Caddx vista unit, will I still be able to use my goggles on the DJI FPV drone? Thank you.

Thank you very much for your detailed Video! It helps me very much to decide to get an O3 Unit or not. I already running WTF.OS on my Goggles and my last question was if it is compatible and if i can use it afterwards with my other vista quads..

hi mad, exists an option to get osd from my fettec fc to the goggle2? with the vista air unit it works but doesnt work with the new 03 system😢 only osd from the goggle works… tnx a lot man👌🖖

Does the new firmware exclude older vtx'es?

I have two drones, one Avata (firmware 1.02.0) and one DJI FPV (1.02.0000)
, one DJI googles v2 glasses, a DJI FLY RC - 2 remote control, is it possible to have two drones in this one bundle with glasses + remote, the task is to fly alternately on Avata, then on DJI FPV, but using one set of glasses + remote control as described above... Another point is that on the DJI FPV drone, I would not like to change the firmware 1.02.0000, since others are not amenable to removing restrictions.
Guys, who has experience using such a bundle of equipment? thank you in advance for the answer.

do goggles v2 record subtitle osd with o3 unit?

Do you have to put the goggles V2 in dji fpv mode before upgrading the dji fw? Or can you update in DIY/wtfos mode?

Hi, thanks for the video! I have a question. Can I connect to DJI O3 Air Unit with a not dji analog goggles? Sorry for maybe stupid questions, I'm only beginner)

Great review. It is very sad seeing DJI abandon the V1 goggles like that after just one generation in between. It would be an absolute dream of mine to see DJI release an update for the V1.

I just got a set of v2's after sending my g2's back 6 months ago. The g2's hardcoded the osd but my v2's with the o3 don't hardcode the osd or create an srt file. Is this normal? So i just lose telemetry?

Nao consigo abrir a unidade o3 dji no windows 10

What about Dji integra?

Thank you for taking out the time to make these videos

They need to make a module, till they do that I will not ever have a DJI vtx

Are Integra goggles compatibles ? It should as they are an alternative to goggles 2 if you buy an Avata drone.

I have Goggles 2 which I use with my DJI drone. If I bind them to an O3 Air unit, will I have to rebind every time I switch between my DJI Drone and the O3 air unit?

I had a V2 and really liked them but got rid of them because they were not compatible with my Mini 4 Pro. But now I have an Avata 2 and do not like the new ones quite as much. I can not seem to get it to give me as clear of a picture as the V2 did. Can i use the V2 with the Avata 2?

Can we use goggles v2 and 03 and still get the video out from digi view ?

Very lost with compatibility! I'm building my own drone, will the DJI V2 be compatible, or are they only compatible with DJI drones using proprietary software? Finding it very difficult to find informaton on compatibility

Hi..great information as usual.👌can you tell me if the new 03 air unit will work with the Avata 2 goggles?? Thanks

please make a video about dji fpv controller 3 support for dji O3 and compatibilities

So i got the gog v2 and O3. Any way i can record the MSP OSD in DVR?

The v1 can compatible in avata 1?

Hi Everyone, there is something I did not cover in this regarding the V2 and binding.

Sadly the same issue that was there before in the V2 goggles that when you change mode you loose the bindings is very much there still today and now with O3.

If you in DIY mode and move to O3 your DIY bindings will be lost. The same stands for moving from O3 to DIY, Avata or Potato mode.

However the previous behaviour of just rebinding one and the rest come back still appears to be there.

This is going to be a PITA for people who want to fly mixed system regularly and it’s sad DJI have not put a better solution in place for this with the updates.

Thanks

Mad.