How to Install H11 and 9005 LED Headlight Bulbs - SEALIGHT X1 Series

Bought some for civic and yes got the right ones h11 and 9005 trying putting them in and they fit loosely in the housing

So what’s the difference between h11 and the 9005?

I have a ford escape 2013 and I checked every thing with the installation process, from correct bulb placements to connecting it correctly in the sockets, though upon turning the light on, it says "LOW BEAM LIGHT FAULT" how can you fix this and do I need a decoder as per manual?

I just bought hi and low for my ram 1500. I was so happy with them for all of 2 min. Then thw drivers flickered and shut off following quickly the passengers went out too. I dont understand wtf is happening. If i tuen off my truck ans start it back up they turn back on again. Any insight?

How many lumens are those

Will these pass inspection?

I just installed H11 fog lights on my 2016 Honda CR-V. It was very easy. It took about 10 minutes and they are a big improvement over the halogens.

Can you have the wire facing down from the LED rather then up?

Doesn't line up straight on Mazda CX-9. I tried it all three ways and the only way it fits snug is with the wire facing down but the chips are 30° off vertical. If I try the method shown above, the bulb is loose and still crooked. Also, about the same brightness as the halogens they replaced. Only difference is color changed from orange to blue.

Its easy as hell when theyre off the car, and theres no rust on the outer cover

These do not for a 2008 Honda Pilot. The connectors are way too small and the length of the fitting too tall. Just doesn’t fit at all.

Will this work in the 2013 lancer high beam ?

My car only has one light bulb for low and high beam, which bulb should I get I ordered the x1 I just got it in the mail hopefully it’s the right one I have 2019 Chevy trax

This video was NOT helpful at all. Probably because I have to go under the hood to do what ever it was you were attempting to show in the video. Thanks for nothing.

Hmmmmm... Mine came with drivers, the ones in the video didn't have them.

Just installed. Easy and looks great

DONT WORK ON A 2014 SIENNA AS ADVERTISED

Let’s turn off the kid music and talk threw this haha

My 13 year old son helped his dad install these light bulbs.

What am I even looking at?

Which one is the high and low ?

2018 Jeep Renegade, best I can do is about 10/4, not 3/9. Any ideas? Good lights, just can't seem to get them to 3/9.

When calling their customer "support" after finding it impossible to get the 9005's lined up at 9 and 3, the lay this on me: "Oh, in the 2021 Ram you need to have them aligned at 6 and 12." Nowhere on their website or in the installation instructions...in fact, the "Customer Support" section is "Coming soon..." - completely blank. Returning ASAP.

My stock halogen bulbs are 9005, and I have scoparc 9005s, but they don't lock in like my oem bulbs... They just spin freely with no 'locking' resistance. When comparing to my old bulbs, these leds have locking nubs/hills like a 'T', while my halogens have nubs like a 'Y' if that makes any sense. Any help?

I wish I found it that easy!

It's always an easy install when the headlights are sitting on the bench. Try installing them in a Jag F-Type and you'll need a curse jar sitting on the ground beside you and a fairly good size box of band-aids. I ended up owing the jar the price of the lamps and almost passed out from the loss of blood. However... once I finally wrenched them into the slots (The lugs are not the same size as the lugs on the 9005s) and twisted them to lock and turned the high beams on, I cursed again. This time it was a happy curse as in... I'll be GD!!!! These thing do light up the night. Flip the high beam lever and small planes started heading for my driveway.

Just installed mine 2011 sierra, both low bulbs were 90° off ...im bummed

will these work on a 2013 Nissan Altima?

Will my rubber boot fit over these led replacements?

“anti clockwise” lol

Your SPOPARC S1 headlights will not index to 3 & 9 o'clock on a 2022 RAM 2500, instead they install crooked beyond 4 & 10 o'clock. Do you have any model than will index properly on this truck?

Got these for 2018 Compass. Impossible to install unless you take out the whole housing

You dont want to buy these, they got super hot and melted the inside of my civic's light it plugs into!

That was for a Kia soul

They don't clock properly on a 4th gen Ram 2500 FYI. Had to drill new holes (in the plastic ring) for the set screw so mine wouldn't blind other motorists. Bumped the install to 1.5hrs as it was a trial and error fitment. Be absolutely sure the lights work before modifying though!

Looks easy when the Headlights are off the car 🤣

Unplug, and plug in, doesn't get any easier than that. Just installed a set on my 04' Highlander, maybe took 5 min.

Will these fit my Ford Explorer 2012 xlt?

Thanks so much guys! I just bought a set for my high and low beams on a 1998 Saturn and yes it's 2021 LOL but it runs like a top and now I will be able to see like a cat in the night

No brand makes these for the 99 to 03 that are adjustable...mine sit in a 1oclock and 7oclock postion and they cant be adjusted...ones i bought for my ram are adjustable with 2 set screws in small increments so i could get them in the 9 and 3 oclock postion...and my 99 silverados led are HORRIBLE cause they cant be adjusted...and i see blue dots all in front of me

2020 RAM low and high beams - look great!

Not for 5th gen 4runners.

I tried installing for my Hyundai Elantra unable to fit them. Th plugs my car have and the plugs sealights have are different.. need help.ordered from Amazon and in the website it says it is perfect to fit. It doesn’t work for my Hyundai Elantra GLSE

Now do it when the lens is in the car.

you couldn't have made a clearer, easy to follow video Sealight! I usually avoid Chinese made products and even if the product is ok, the instructions and documentation are usually terrible...but this is well done.

My slit in my 4Runner is too big for them, awesome

I bought the high beam low beam set but the kit doesn't say which is the high and which is low, the bulbs look identical, called the support number and all i got some message in Chinese, if I had known this was a Chinese brand i never would have bought them, very frustrating!!! Should have been straight forward!!!

I installed these on my 1997 Tahoe.
Dispite the yellowed aged plastic Chevy headlight, the bulbs still are bright enough to make people flash their high beams at me.
I did a Low/High all 4 on wiring, and with all 4 SeaLight LEDs going, there is no need for a light bar in dark mountains and rural nights. These are what your looking for

I bought LED S1-9005 HB3 kit made by IRONWALLS FOR MY 2005 Toyota Highlander and they didn’t work. They looked exactly the same as in your video.
I installed it where I have 9005 in day time running socket. They are positioned inside close to the grill on the car. Is it possible that +& - are marked wrong on them? Is it ok to try with reverse polarity?

Does any part of these lights get too hot where i have to worry about it burning other wires inside the light compartment on my buick encore?