Manual Lveling ANYCUBIC i3 MEGA

Guys! if you're not going to have voice over for these at LEAST have a high contrast font color for your subtitles. this is unreadable for me on my phone.
I do voice overs as a side hustle. I'd be happy to help you guys with that.
Otherwise, these videos are great. Good job!

Thank you, I will test this in the morning to see if it fixes the little bit of shift I have been having.

I bought a printer this January a Mega S, and just started to not adhere on the plate so I did follow your calibrating test but ...... it's isn't working, and needs to be improved
why? because after adjusting the left and right of the bridge when I hit home for all, the z-limit put it all in the same position...;(
so after 30 minutes, I have to repeat the process again, but this time I take into calculation the z limiters(both of them) started with the motor off.
so I adjust the front 60mm-left-right, then put the z imitator from the upper screw to max down( I use the caliper to keep the front at 60.0mm), after this, I put a motor on, and hit home all, now you have a level left-right( mine was about 62.3mm), and if you want to be lower adjust from left and right z limit screw about 1turn of screw equal; when you are satisfied with dimension, check again if left-right is equal if not block the motor adjust the long z score a bit, and the small screw z-limit to be in line and equal. put the motor on, check home all, and measure left-right in the front to be equal.
After this start calibrating the table corner and middle.

I think the printer can be made easy to calibrate from construction, but this is in a separate discussion, a private one;)

Good luck when calibrating and then printing

anyway to perform z-offset calibration in anycubic mega s?

Thanks

I just in the past two weeks purchased a anycube mega S and seriously need help trying to level the bed the front left end I have to adjust the spring all the way open to a point where there is no pressure on next spring where are the other three seem normal I hope that’s making sense and it still isn’t leveling properly.

Fraud Copmany, unprofessional after sales support, No technical support provided in person to fix their FAULTY products. They keep you waste your time in online troubleshooting yourself and get them outside of warranty period. I had a terrible experience of purchaing through their aliexpress store, BEWARE

From where can I get the glass

I am attempting to level my printer. When hitting "home Z" the motor makes a loud grinding noise and nothing moves. Anyone know how to fix this?

Good evening. I wanted to know what modifications I need to make to my anycubic mega s to be able to mount a leveling sensor? What version of firmware do you have installed? The "S" version does NOT have this leveling feature!!! Can this item be added to my machine? For the moment thank you and I'm waiting. Greetings.

great video.

Thanks, this really helped!

After you manually raised the left Z to be the same distance as the right Z you didn't adjust the left limit switch, so the next time you zero the Z you will have the same problem.

Z axis leveling shall be done against Y axis. For bed clearance, use a thickness gauge, make sure to measure a heated bed. Then use a custom Marlin firmware and do manual bed leveling. Iterate a few times with bed leveling active (M420 S1) and adjust matrix manually. Finally heat head and adjust Z offset. The whole process takes 2-3 hours and involves typing g-code commands to move head around. It is definitely not an easy task for starters and the 4 corners adjustment is definitely not enough. Nothing is really straight with this printer, I have up to 0.12mm (!) difference between highest and lowest points. You won't work out for that much using 4 corner alignment only. For ref, paper height is 0.1mm.

The left Motor when leveling dosent stop

I don't understand why you would turn the lead screws without resetting the microswitches, Without changing the switch positions the lead screw changes will be lost when it homes again

Il video è fatto veramente male, tutto troppo veloce e confuso.. mai visto un video peggiore..

"T0 sensor abnormal"
How i can fix it ??

Hola quería saber si los motores que mueven el eje x tienen juego

IF YOU HAVE WARPED BED:

Download and flash Marlin firmware for Anycubic i3 Mega (it's the same as factory firmware except updated). In there will be a new program to calibrate warped tables - it's a bit involved but it works perfectly! If you're not sure, it's OK because you can flash the old firmware anytime. You can use Cura software to flash the printer firmware.