Комментарии:
What's it going in. Where's that video😢
Ответить15w50 in a high performance engine is a complete mystery to me, i've worked in the racing industry for 20 years and just don't understand why you would use such a high viscocity oil in a built engine, your tolerances should be really tight meaning that oil just isn't going to lubricate and will cause many other weight and power sapping issues
ОтветитьI wish there is a good machine resurfacing shop in my country that do similar job to my engine ( i am building a m50 super built but still haven't done anything significant)
ОтветитьSo its a rb25 stroker
ОтветитьBro give a proper info like you skip the timing belt part, show us the timing and the cames cuts and cranke timing. 🙏
Ответить"if quinn build it, we trust it."
ОтветитьHow much is the whole build?
Ответитьมันเป็นเรื่องง่ายๆสำหรับคนมีทุนมากกว่าคนอื่น
ОтветитьRaw dogging that crank no assembly lube no nothing is crazy 💀
ОтветитьG35 900.... LoL "1000hp" build click bait title with a 750whp turbo.
ОтветитьGareth Bale 2.0
ОтветитьReally nice build with some pretty impressive pars. The block brace is nice.
ОтветитьYou forgot 3 Bolts on the Head. Other than that cool build :D
Ответитьwhy use a 25 block and not a 30?
ОтветитьYg indo sini la
ОтветитьSome eat dinner while watching movies. I ate dinner while learning about this engine. It was riveting 😅
ОтветитьThis looks like a fun build! However, I’d personally check the piston ring gaps and bearing clearances with the head studs, gasket, and a torque plate installed, as well as the main girdle and sump brace installed and torqued down to get a more accurate measurement of the correct clearances; the amount of force applied to the head studs and main studs when fully torqued down are known to cause a measurable distortion in closed deck cast iron block sleeves, as well as main bearing journals, especially in RB25/26’s.
ОтветитьMindblown😮
ОтветитьThe intake ports on the rb26 look like 3 Weber side draft carbuerators would bolt up
ОтветитьБеларусы конечно молодцы
ОтветитьBro way to much silicon that your are using for the gaskets of the water pump and the other parts. If you use that much it could get in to the oil canals and block the oil from going up where it needs to be 😊
ОтветитьMaybe I just don't understand rb's but how is this a 26 if it's a 25 block?
Ответить1 000 HP??
ОтветитьBe interesting to know engine dyno to in car dyno then stiffer bushings an re dyno?
ОтветитьDyno?
Ответитьbuild a ford barra, the best inline 6
ОтветитьBro where’s the 300zx
ОтветитьVery nice Job on amazing engine build I have seen
ОтветитьEpic channel !!! Love your videos and how you do complete from the ground up performance engine builds. Keep it up and thanks.
ОтветитьAssembles worlds most beautiful engine, than installs rusty thermostat housing/neck on it LOL
Ответитьput this in my buick encore
ОтветитьHow much power did it make? Seriously doubt it will make 1000+ with a g35-900 turbo?
Ответить13b/20b/26b
ОтветитьGuys, what kind of camshafts did you put with this turbine? 270?
ОтветитьWhere can i get this lego set?
ОтветитьYou guys should build a 4AGE. Hardly anybody does content on them and you guys would give some much needed insight into the engine.
ОтветитьNice vid and all this stuff but how's the turbo or the engine going to survive with an 15w50 oil? I know its 100% synthetic, competition oil etc but 15w50 is usually used for N/A engines if u ask me.
ОтветитьLet me pause and save this for when I’m not baked
ОтветитьFucking stupid custom made oil pick up
Ответитьmy mechanic when i tell him i need to pass inspection
Ответитьi love this so much man.. please rebuild some v12
ОтветитьItalian piston and rods I used them on my 2001 Porsche.. amazing quality
Ответитьwhy is there guns sounds
ОтветитьI wonder if I can reverse engineer it by getting every single part he got and following along with the video
ОтветитьYou should have taken the rod cap off and measured the plastic gauge
Ответить