Ring Final Circuit Testing Revision Video

Thank you, very easy to understand. helps alot

Lovely quick video for 3291

Brilliant, excellently delivered lesson, thanks for making it so clear!

In my house I'm getting a reading between r1&rn and getting reading between conductors but getting 0.00 in r1 and r2 what could it be

Thanks for the video well demonstrated and explained.

Very clear and easy to follow. thanks

Superb sir an excellent video.
Very clear sir.

I don't see why it will go up if the socket is reversed

Bit confusing about the regs .where it’s the safety no fuse on the spur ,two wires from the consumer unit one on the spur same csa🤔🤔🤔can anyone explain???

Downthumbs are from competing course providers :)

Dear sir a most brilliant video.superbly explained.very clear and concise.thankyou most kindly.has helped me out loads keep up the great work abs videos.

sir can I electrical work without education certificate

One of the best videos Ive ever seen !

Great teacher

Another great video

TOP VIDEO. TOP INSTRUCTOR. THANK YOU FOR UPLOADING

Does it necessarily follow that, after the installation of a new Consumer Unit, there must follow a whole-house electrical safety check that is similar in extent and scope of any ordinarily ordered domestic electrical safety check? I really don't know this subject and I'm asking it from an angle of don't-know-anything about the Trade, at all, so be gentle with me, if you would.

Trade skills are best. Thank you guys for best time a have spend at your training centre when I did my level 2,3 . Best training in UK

Hello! Tell me please; is that type of a circuit, so called "socket ring circuit" you have in each house in U. K. ?? Very interesting (?) what is the reason for that type of wiring the socket’s in the ring??
Can you tell me please (?) why you do that for??????
What is that ring good for???
How it is working???
Can you please answer in the video (?) so I can get to the point of it, please???!!!!

Why can't all teachers be like this. Easy to understand and great at explaining the purpose of what he is testing. Great work, hopefully you do more videos on testing.

I don't get what the 4 resistances are? 4 sockets?

Very helpful. Finally!

Very detailed. Thank you

That was a useful summary and very clear, but you didn't look at all at the really interesting entry key case of a cross connection on the ring which you showed on the first diagram. I can see that a cross connection could give some puzzling results during testing and make it impossible to reduce the normal numbers, but I've always struggled to see why it might be any kind of safety problem in normal use of the circuit, in fact it seems to me it should improve the performance of a ring.

Very good indeed. Couldn't be clearer.

At exactly 5.12 sec you say on 2.5mm / 1.5mm T& E the reading should be 1.67 times higher due to the smaller cpc cable. However, On my house the reading is only 0.2 higher. IE. L1-L2 is 0.22 N1 - N2 is 0.22 E1 -E2 is 0.24 My Question is what does this small cpc reading show? The circuit operates ok. But id like to know what it tells us? Also on the cross connection test (L1-N2 & L2 - N1) the reading should be HALF the L1 L2 reading but on mine its the same 0.22. what does this mean.?

Thanks for this vid, it's been one of the most straight forward and clearly explained videos I've seen 👍

Why for r1 and r2 you test all ring and radial together ?

Thank you .very clear .

amazing thanks

That wiring on the test board is rough

Not a spark but great clear and informative video even if your bad at maths this breaks it down so the reasoning for readings is clear even for inumerate types. have saved this to my watch latter folder.

thank you .. I figured out that my emmersion heater was causing the problem with the ACE THANKS

sorry also need for cooker and installation resistance test

this was great we need yo to load for cooker

I finally understand it after watching this video. Thanks

That's why TradeSkills4U is the best.Thanks for that brilliant video.

Sir Bless you!

I was told to call it a socket adaptor rather than a socket tester, that's sparky terminology for you though - it's not a bulb, it's a lamp! :-P

Excellent instruction; thank you.

thank u sir []

Very well explained

rings are a disgrace and should be banded

Can you explain why you expect the grounding wires to have a higher resistance than the line and neutral wire? I would have expected them to have an even lower resistance than the others.

I am not an electrician, but I would have expected wires to be be correctly connected and checked physically and visually. With good workmanship all this fancy testing should just be an extra. I suppose there are plenty of cowboys about. If there is wrong polarity in a ring I would have thought it would trip or fuse or worse, so you would already know there was a major problem. I still refer to wires as live or positive, negative or neutral.and earth or ground. I like to understand what’s going on when I engage a tradesman, so for me it’s an excellent video.

سلام خیلی ممنون از زحمات شما

I really like this Kewtech testing equipment, must get a one