Комментарии:
thank you
ОтветитьI wish i knew how to post pictures on here of the wall i have to render in the next couple of weeks, we have hacked off old render that had cracks appearing but soon realised the render was actually as good as you can get and was a nightmare to remove that then only left 1 outcome for the cracks, the brickwork had large cracks all over it, there was no mortar in the joints, every service was being brought outside via that wall and the plumbers had butchered the walls and filled the holes around the pipes with pieces of brick. Not to mention the lack of mortar had caused some bricks to push towardds the cavity as we were hacking off. We came off the job and got a bricky in to make the wall right for rendering but have no idea what we will return to but i can honestly say working around 5 yes 5 windows and door will actually seem like a walk in the park no doubt.
ОтветитьWhy even bother with using mesh?
Ответитьhow many bags you use?
ОтветитьSpectacular work man. Turned out great. Painted up nice with a few brackets and planters and it could set off the brick wall lovely.
ОтветитьWould you use Weber OCR to patch a fairly large repair on a blown cement rendered wall?
ОтветитьIt's not falling down, so what's the issue?
ОтветитьBrought to you by Refina.
ОтветитьSmooth as silk. Well done. Need a wall doing, can you sort it?
ОтветитьHave to say, that is one of the best videos, and best results (considering the state that 'wall' was in. You're clearly fantastic at your job. Proper master tradesmen, they are thin on the ground..
ОтветитьHi - I have a repair to do on the front of the bay. The horizontal is fine but the angled bell went all green and the concrete paint went soft / permeable. I have scrapped off about 4mm of render some of which was damp so obviously moisture was getting through. Should I remove the lot or can I just patch over the existing render? Its a strip the width of the bay by about 9 inches on an angle? Do I need mesh to give it strength considering what has happened?
ОтветитьHoya mate have you dont any of the coloured one coat renders? Can they be scratched?
Great work bud i think youve convinced me
That’s a rustic finish ❤
ОтветитьSee extensions Dya bead same day and all with the Weber or bead day prior
ОтветитьHello sausage 🤣 what did you use for the scratch coat? Was it sand and cement and then the weber ocr for the final coat?
ОтветитьI have a very poor Tyrolean wall that needs a lot of knocking off and patching. Can I apply Tyrolean over the already painted surface. I’ll use your tender and primer for the patches but I’m worried about going onto the original surface when I blend. I love your videos and I’ve learned plastering through you and your kindness to help people like me. Thanks very much
ОтветитьIs this webber ocr a breathable product like lime render?
ОтветитьI’ve been following you for years, you helped me learn how to plaster (DIY level any way lol) and now how to render walls. Thank you!
ОтветитьI would of fixed (plug and screwed) EML, Galvanised Expanded Metal Lath or Galvanised External/Internal Rib Lath sheets to the wall, then applied two coats of a sand-cement-lime mix, using 6 parts plastering sand, 1 part cement, 1 part lime.
ОтветитьReally good work but here in the states my competitors would charge $300 for a wall like that and just one shot a thick coat of quick set and texture it out. Very frustrating here to do work properly.
ОтветитьI need to re-plaster a wall that has acrylic paint on it. What would you use to get a good key please?
ОтветитьGreat video, Could you do more on the power float, tips, technics, timing's etc 👍
ОтветитьThat came out perfect, I have a 50m perimeter wall looking as rough as that one did, might steal your technique!
ОтветитьWeber looks lovely to use, what's the coverage per bag?
ОтветитьHi Blaine I’m going to try my hand at plastering one wall in my bathroom.I’ve ripped the tiles off obviously half the plaster has come off with it so I’m going to take it down to the brick.have you got a link to a video that takes you through all the stages.also has a small window with a deep recess.
ОтветитьI think I'll try that weber stuff
ОтветитьHi Blaine will you be doing a follow up video about using the roller to apply skimcoat plaster?
That was a great topic!
Brilliant
ОтветитьComplete nonsense to knock the wall down or build one next to it, if you want it 100% straight just use polystyrene sheets or hard insulation sheets and then you can render it. Other alternative is decorative or real stone tiles or composite cladding, but why knock stable wall, doesn't make sense
ОтветитьDo you have a link for the scabbler blade?
ОтветитьGood effort Blaine 👍.
ОтветитьGreat chanel bud watched most of ur tutorials 1 question im from Ireland and the most common sand and cement finnish we have is a nap finish the a napping sponge iv looked 4 this on ur videos and have cn u do it??
Ответить👍👍👍
ОтветитьGet yourself a plastic draper hawk man. You’ll never look back. 10€on Amazon.
ОтветитьAlways use mesh in my rendering work
ОтветитьHi Blaine, I notice you render to the floor without any drip/bellcast beads on garden walls, doesn't this cause any issues?
ОтветитьI think that primer only allowes for 25 mm of render tho
ОтветитьNice job! Try turning the mesh the opposite way it’s rolled mate! It won’t curl away from the wall-and is easier to bed in ! Just a tip that I do which until I was told never even occurred to me👌
ОтветитьTurn the mesh over so it’s not pulling away from wall. Its finding the right bagged gear that suits yourself. Some are a nightmare hawk and trowel.
ОтветитьHi m8 what attachement did you use on your power float
ОтветитьReally good job with what you had to work with. Have you done any vids on how to do rounded surfaces like a bay window?
ОтветитьWeber, sponsor this man!! I'm sure more people are buying thanks to Blaine 👍🏽
ОтветитьAlright pal, when we are using hp12 to sort out poor walls like this, we’ll blue grit it, coat & mesh and once it’s gone off, we will pin the scrim coat with the big plastic polish and pins to secure it. Just a thought👍👍 always good to see someone else work 😂👍
ОтветитьLove it pal 👍🏻 speed skim crew 👍🏻
ОтветитьLove these vids mate.
ОтветитьNice job, you have done exactly what was asked and smashed it! I’d be over the moon with that “tidy up” job
Ответить👌
Ответить