Marlin Firmware Install Under 5 Minutes [ 3D Printing ]

I have a Sunlu S8, would this fix work?

Thanks i have a tevo tornado that stop working on the bead termistor and the new bord is about to arrive

dont you need the EZboard though? I have a ender 5 plus. the firmware link above will say It will also need the LCD adapter board that is intended for use with the EZBoard added on. So the EZ boad is not the stock board?

It's the film it's pronounced center adding that to that film where and the bill touch just please let me know cause then I know if I need what. I need to do alright thank you

Can you use this method to upgrade the firmware of a Makerbot 2 printer? Thanks!

When I 3D print my 3D printer nozzle keeps going to the right I need it to print in the center I don't know if it's my Marlin I need to fix or what it'd be really helpful if you could help me thanks

does anyone knows if this works also for a printer made with Arduino mega and ramps board? i have a homemade built..

That was the best information I’ve had!! Thank you so much!!!

i know u think your helping, but it just doesnt work the way you show

Hi Santube, I have a standard CR10 with a v1.1.4 board. I want to make sure nothing will mess up if I do this DL.

not sure how you did any of this cause there is no more open firmware windows anywhere. So not sure what this is all about. I got an ender 5 pro that is basically just a damn brick right now cause I cant get it back to factory firmware. They couldn't have made this update process dumber.

Hello I have a question about the printer marked i3 v2.1 motherboard marked I3 V2.1 mother Melzi marked Repetier Firmware 0.92.9 for Wanha Duplicator I3. Installed Arduino Uno repeater, can I now the Arduino ide program pole and a USB cable to make a new program to keep the belt on, do I have profile navigation and e.g. 1 mm x or y axis settings on the actual trolley will go 0.6 mm on I foster a step change. can it be done and advise on how to do it?

thankee thankee! not sure what I forgot since my last time doing this but your video just set me straight

How I can find what Board I have to use? My Arduino is a bit different to the one you showing on your video. Is defaulted to Arduino UNO but is not working. I tried others like MEGAs and Leonardo but I get the same error message. The "Get Board Info" doesn't give me any information, its says unknown.

man Santube, I think I got my cr10s around the same time you did and I still find myself circling back to your videos when I have troubles, you've come so far. Thanks so much for you content

I have a question does this method work for an easy threed K7 printer. I'm trying to upload the newest marlin on it.

im getting avrdude: stk500v2_ReceiveMessage(): timeout error and it spams it like 6 times and stops the upload

What printer is this? I am looking to upgrade the lk4.
?

I keep getting this error with ender 3 pro.



Using Port : COM3
Using Programmer : arduino
Overriding Baud Rate : 115200
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x6e

avrdude done. Thank you.


Can anyone help me out?
Thank you

my printer doesnt print anymore after failed attempt ender 5 pro

Hi did what you said but it doesn't have Mingda 2d

Good afternoon, I tried doing this process with my cr10 v2 and it keeps saying upload failed. So when I when to check devices, no comport showed up. What am I doing wrong, or what do I need to do to update the firmware ?

port not show

Nothings coming up on my port what does that mean

My screen says COM1, there is no COM3 option?

Does this work for a 32 bit board v4 2.2 ?

how do you include a heated bed for a anycubic mega zero?

Does this work for the jaguar printer as well?

Thank you after watching 100s of video on how to upload firmware for anycubic mega zero I finally managed to do it with just watching this one. Thanks for sharing

ok idk why but it only shows port 1 for some reson

I've had my printer for three months. I've been told to upgrade my firmware. I own a CR-10 V2. If I follow this video I won't have to go into any files and make changes? I want to update to Marlin TH3D. Nervous abut messing up the Firmware.

how do i choose for crude build ramps 1.4 and arduino mega 2560 3d printer

do i need Arduino board to update ?

can i use for ender 5 pro to udate firmware ?

Hmmm it says problem uploading to board. Programmer is not responding

How can I change sd card files sorting (sort by date, newest on top) in marlin firmware. Ender 3 board v1.1.2

I received an error message when updating Marlin for ender 5. It says, problem uploading to board

I got an error avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0xfd
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0xfd
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xfd
everything looks right

Hey does this work on the kingroon 3

How can i enable power loss recovery in ender 3?? Please help me out if possible

Got all the way to uploading but it stopped saying there was an error.

Is that able to work without bltouch sensor

YES ABSOLUTELY TRUE.........!!! THANKS FOR YOU AND TH3D TEAM......!!!

Creality Ender 5 Plus with the Creality Silent Board, (a different IC), and a duel display but using a Bigtree Smart Filament Sensor and of course the BL Touch

Hi Santube. Good video. I have a cr10 I guess that this includes the firmware. Also what is the advantage of me upgrading the firmware. I’m not sure if it’s ok but I thought there was issues with the th3d firmware. Thx for the video.