Understanding the Charge LEDs on NOCO GEN & GENPRO

Is there a way to check the battery levels when not plugged in?

If im low on time can I unhook the battery and use it if it was still blinking green?

Well I'm about to leave mine over night on a AGM battery but I had it on there earlier & it's not showing anything is damaged but it's just pulsating @ 25%. It was on there for about 2 to 3 hrs & never passed that. Then I turned on the other mode for completely dead batteries. Came back later & just the Power light was on & the mode had stopped. I would have assumed that it would have continued sometype of charge. Then now that I noticed I put the settings back to AGM mode & it's still @ 25% after the past 2 hrs still. Am I doing something wrong or will I wake up tomorrow to a full battery?

Got to the green light unhooked it, then hooked it back again and back to the second red within seconds. Something is off

I'm completely new to this, how long do I plug the charger in before use?

No way. My battery had half the volts and no amps - and after 3 minutes on the charger shows as fully charged.

I purchased genius pro 25 to charge it from the socket do i just plug it in, all i see is a yellow stand by light, none of my bars are lighting up, does it take a while for the lights to come on

what’s advance maintenance mean

Why is mine stuck with a slow pulsing red light? I can’t find the answer anywhere.

I really like your product, but your charge leads are toooooooooo short. I have a 22ft pontoon. The charge controller is under the captain's console (middle of the boat). The battery to start the main engine and run all the lights and equipment is in the rear, but the electric trolling motor batteries, additional transducer, and electronic compass are in the front. None of the charging leads reach any of the batteries. I had to buy my own wire and connectors to make extensions because your leads do not support a way of extending the leads without nullifying the warranty. I did not nullify my warranty because I also made connection terminals at the end of my extension, so no modification to the charger was made. Now I am 3D printing boxes to protect the terminals I made. All in all, it cost about an extra $100.00 in materials. It would be too easy to put SAE connectors on your charging leads to allow for extension to be made from readily available automotive parts.

Would this charger be good to charge multiple group 31 950cca batteries

Can you use this on a Car battery?

who else was just looking for the tdi ship

I am wanting to buy a NOCO Genius Pro 3-bank 30amp charger for my boat, but my question is: My boat is Wet Slipped at a Marina, so I’m not with it “all the time”.

Is this charger suitable for off-site full-time plugged in charging? Meaning, when we leave the boat, can we plug the charger in and “forget it”… then come back a week or two weeks alter, and the batteries are good to go? Does it have that sort of smart trickle charge capability?

My Noco genius 10 going Trickle charging on 25% charged battery (i check it with battery tester) why's that can help please? i tried on 2 different batteries, and the same thing happened

+I checked the batteries with battery tester showing SOH health of batteries 95% and 100% they're maximum 1 1.5 years old batteries

Mines is blinking green slow green pause every 4 seconds what does it mean

*YOUR PRODUCTS ARE JUNK, 3 ALL DIED, ONE WOULD SAY OK, ONE DIED, BUT 3 ?*

Is it normal for the 25, 50, and 75 to pulse in succession (like it’s charging normally), only to all turn off and start the cycle again? Hooked up my Genius 10 to my motorcycle at 11.9v as per multimeter and that’s what was happening. Eventually the green 100% LED went solid, but it just had me curious.

If my car sits for over a week w/o use.... Is it ok to use a 1A charger (on an AGM battery) like a Noco Genius1 instead of the using the Genius10?

Have not used since purchase. Plugged in and could not get to come on. Keep trying until all lights are flashing.
Restart and cycle to proper battery type then after a few minutes all flashing again. Bought in march of 23 am I screwed ?

I have an agm and a lithium wired in parallel. Can I charge them both together wired in parallel using a noco 10x2? Or should I unparallel the batteries first?

My green LED has been pulsing for 3 days now is this normal?

Mine is pulsing 25% and power one at the time

Can’t find why this is happening. New lithium battery. It won’t charge