Комментарии:
I threw this on my custom ct200 and it went 55 right out the box
ОтветитьIdk why but my ghost bogs at low rpm
ОтветитьYou didn’t need to lap the crank for the flywheel ?
ОтветитьI hope you get the comet belt, nice build those cheap Amazon belts melt right to the clutch. I had the juggernaut too amazingly different
ОтветитьDo have a fuel pump or is it gravity
ОтветитьVi build a Predator 212. I didn't run it until I billet proofed the engine. Took all of the junk parts from the factory out.
ОтветитьU interested in building me the sane set up ?
ОтветитьNice mini
ОтветитьMan’s got on the socks with the flops😳🤣💀
ОтветитьBone stock ghost, juggernaut, cvt set. 10t drive 38t rear on my trailmaster hurricane and yesterday hit 61.6 mph dirt tires as well. 19x7x8
ОтветитьWhat carb is that
ОтветитьWhere do you get front bake and stuff
ОтветитьThought u wasn’t supposed to hit the crank without the bolt on it?? Also with the billet flywheel aren’t u supposed to lap them in with lapping compound???
ОтветитьIt’s been a year have you broken in the engine yet we need to see her at her max 🤞🔥🔥🔥
ОтветитьCan u send me the link for the exhaust you have on the ghost
ОтветитьId use ome valve lapping compound to make sure your flyheel is snug and level but geat video
ОтветитьLapping the flywheel is highly recommended
Ответитьdid u use hemi or non hemi flywheel
ОтветитьSorry to ask such a lame question and I really appreciate your time. How do you get away with driving on the streets? I love my Peter New Hampshire and I’m wondering how far to take this and whether it will be streaming or not one other question what is the name of the fly wheel? I need to do my homework here I just picked up a ghost is the list that you have everything that you put into the motor?
ОтветитьNot bad speed, but it took too long to get there
ОтветитьHow did you set that chain up to be on the opposite side?
ОтветитьWhat torque converter is it?
ОтветитьWhat ignition coil
ОтветитьNice build 4 stroke bike
ОтветитьWhere can I get that gas tank?
Ответитьis the gas tank gravity feed or do you still have to use the fuel pump
Ответитьwhat tires are those
Ответитьtake off TC. my ghost without TC goes 75+
Ответить56 mph on mine just by changing the rear sprocket. 73 to 53 tooth. 😮
ОтветитьI know this is an old video but I hope you do see it, you need to adjust your carbs needle because you have some mid RPM hesitation, when you're doing the top speed run I can hear it hesitate like right in the middle and then once you hit I think 38 mph that's when it started picking up and sounding better and healthier.
ОтветитьMy ghost motor does that stock with the juggernaut
ОтветитьGood job on that mini👍😉
ОтветитьHey let me get that old flywheel I’ll pay shipping
Mine flew apart … without a cam or stage 3
Nice job!
Here’s a tip. Don’t waste money on the ghost if your just gonna take off the rev limiter lol. But a regular 212 and a stage 2 kit, and boom cheaper and faster
ОтветитьWhat Ignition coil did you get for the motor?
ОтветитьBest way to break in a motor is to run it the way you intend to use it normally. So balls out! Learned this from a engine builder that built race engines for Nascar and dirt track cars.
Ответитьin this video do u only have all the parts on the engine in this video because im think of buy just the engine and ignition coil and fly wheel
ОтветитьDoes the 212 ghost have a governor?
ОтветитьI installed it but now my pull start isn’t working correctly
Ответитьwhere did you buy your cell phone holder ?
ОтветитьWhat torture converter are you using?
Ответитьdoes the ghost have govenor in it
ОтветитьDo you know how to get power to the headlight using the ghost motor?
ОтветитьCan you post a list of all part numbers
ОтветитьI have a CT200UEX 196 cc. Billet rod and flywheel cam 26 springs 22 mm carb and it does 60 no problem. I have a 212 built the same that vibrates like it wants to bounce you out of the go kart.
ОтветитьBreak it in like you're going to be driving it. Don't baby it, unless you're going to baby it forever. You need a good shakedown as well.
ОтветитьHow many RPMs is that thing pushing?
Ответить😮💨
ОтветитьI wish someone would make a high quality full suspension roller without engine.
ОтветитьDidn’t even lap the fly wheel smh failure coming soon, this is a terrible video, do your research before posting stuff like this
Ответить