Full MikroTik MTCRE - Introduction to VLANs on MikroTik. (Episode 1)

Which is the best method to use for VLANs and VLAN trunks that would give the best performance.
I assume the software VLANs, are going to go via the CPU, so the overall bandwidth would thus be throttled down to the CPU bandwidth.

This vlan config makes me rage hardcore

As always, the way you explain about topic is awesome, i like that you break whole video into different sets and third set was most difficult to understand cause i am at learning stage, better if you can provide an identity to router which can be visible in winbox window while you are doing configuration on it. so that we can understand on which router we are currently working.
i would like to thank you for making such a informative and wonderful videos which makes learning a fun. Thank you.

Awesome!!! But these options are not best suited for any device. You need to check the VLAN switching support pages to see the optimal configuration way for your device. And abstracting the bridges differently than your device's chips, can lead to CPU load, throughput bottlenecks, or even weird routing or not working at all

That is a great resource ! This will help with my homelab setup.

Pls suggest me

Hello
I am interested in configuring a voice vlan and a data vlan for a voip phone
can you help me?

to complicate....i try but it is to much with bridge setup.... to many details.. need this but not manage to setup...
i have main router and on that router have bridge.... and that is problem, can't isolate one port for VLAN on switch connected to that eth5... 7.8 is version....

Thanks so much for your Video. I have trouble to install VLANs on my Network with the Microtik Router OS. Put now everything works fine.😅

Great Video, thanks man, you are a genius on Mikrotik.

if i have a mikrotik router board, the trunks you talk about going to device 2,4,5 or can these all these be virtualized by the main router board or are these other physical devices?

Your explanations are much better than most written online resources and easier to understand than Mikrotik's own documentation. Thanks for these videos!

Thank you for sharing your knowledge.
I am new to VLAN; I have just on router, and one switch, I wish to configure 5VLANS on 5ports on the router, and then connect the same ports to my switch where APs can pick the IPs and broadcast to it's devices.
Please help me

Huge thanks for the shared knowledge. I enjoy watching the channel. Can you tell, please which environment is used for the simulation?

This video is really helpful, thank you. How would one use the untag feature for a CAP assigned to a particular datapath?

Too fast for me...

Hello. Which version of MikroTik OS and file type did you use to get 10 interfaces? Each CHR I download only gives me 4 interfaces. Thank you for your uploads. That have been helping me extensively!

nice, but in my opinion, you are mixing L3 with L2 in your design. I would not do it in this way but all depends.

I am having issue with which method to use, i tried the bridge method without vlan filtering i can only communicate with some vlan and not other. I trying to add trunking to my exsi server

how to tailscale on mikrotik?think you .very

Thank you for the video, one thing though, If I do separate bridges for each VLAN on the main router, won't that mean that it wont have harware offloading turned off?

I thought this is easy like this, and didn't work. I watched the video, and he does the same I thought it should be done to make it work, but they cannot see each other as neighbours, nor can ping each other, but they are directly connecteed. Does anyone have any idea? I try to make it work between a RBD52G-5HacD2HnD and a LHGGM with no luck :(

Hi Thank you so much for the information you share. Great job. Very interesting, but do you also have videos on how to create a VLAN with a router/switch that has 2 switch chips. And the app eve that u use, is this an app specific for mikrotik virtual environment. for a test environment.

hi thanks for the info but do you also have examples that are configured on one router.I want to create a separate network for my smart home products

so confusing, you did it very quickly and switch between windows and winbox. try to make it a little understandable. thank you anyway

Great job! Thanks.
What network drawing tool do you use?

your awesome

just found your channel and went over your VLAN and bridging videos on mikrotik as a refresher, very awesome material!! good pace and easily digestible, thank you for creating this content! If I can request a video suggestion for the future on how to create a span port, have searched high and low for this topic and to no avail. Am basically attempting to practice auditing my own home network traffic via a pcap capture but having trouble trying to learn how start with configuring simple span port/interface etc. Cheers!

i am happy that i found this chanell, am still learning mtcna but am sure this mtcre videos will be my guide after classroom. whenever i want to further my studies. hi sir, do you think it a good idea to dive into mtcre right after mtcna?

Great video, thanks! Wait for a video with vlan on one bridge with all of mikrotik interfaces. Thanks a lot, it's very helpfull

Way too fast. I lost which switch you were working on many times and had to go back many times. The "follow which switch I configure"' ask too much in my brain to follow the "understand what I am doing".

What would be the easiest way to block inter-vlan routing but allow for example my IT vlan to communicate with all of the VLAN's?

how soon can i talk to you

hi
i will to know more about vlan on two to three route

It's great video. Thank you.

This was awesome, I needed a simple way to do the vlans based on Cisco's concept. The last method was easy and clean. Thanks.

Great, great, great explaination! Thank you!

Next time you do lab please change default names of routers to avoid confusion, and thank you for sharing your knowlage

Bra, het iemand al gese jy lyk soos die dude van Linus Tech Tips haha, nice.

I mean... video is great. But its my 3rd attempt of understanding it and still i don't get it in 100%. Maybe it's for the advanced users. I'll let my co-workers run the network infrastructure.

why you not do a new way of vlan on main MikroTik1 ? This is the most importand part and you not do that. How we should create vlan in new way in router on stick ? How create dhcp-servers on new bridge way. What with Hybrid port for WiFi AccessPoints ? What when I use 4 cables to stack of switches by LACP... how then use that New Way of VLAN - Please create a new video, of course this is out of MTCNA but this video must be created !!! Please do that video as Part3 :D. I wait for it.

watched edgerunners and wanted to watch vlan stuff to get it off my mind lmao. saw the intro and everything flashed back

Thank you for the explaination, I'm new to Mikrotik and this video has been really helpful

The way I've created vlans (vlans for the router side, not Switch side) across multiple downlink/trunk interfaces is make a single bridge, add all the ports I want as trunks and create the VLANs on the bridge interface. First time I've seen it done that way (example 3).

I'm assuming the way I do it is fine as well? Something I've learned in my time with mikrotik, you can make just about anything work that you want. The skill with mikrotik is making it work efficiently. Problem is, sometimes it's hard to tell if the way you did something is actually efficient or not. LOL the things I Set up and work fine in my lab may not necessarily work in an enterprise setting with 1000's of devices requesting dhcp and dns, etc.

Great video. Had to slow it down for the 'third' way you covered. Still seems like the MT way way of doing things on layer two is overly complicated. But you do a great job of explaining it.