How To Replace any Smartphone USB Charging Port Without Heat Gun properly

Sir,jo cycle ki rechargeable headlight ate hen uski charging port ukhar jaye uha par naya charging port laga sakte hen ?

❤❤❤❤❤❤,EXCELLENT WORK BOSS

brilliant

this is method not supported

Which is the best solder wick to use, I bought some but it doesn't get out of the holes to put the new one in, TIA.

I have problem in mind meter the usb

I feel like I'm being gaslit.

It's working for my phone.Thank U so much.I have no idea for that because I have no hot gun. AWESOME Sir

Nice work especially when you put it back manual

I've gotta cal bullshit on this. There is so much heat on that board and on the other components they have to have damage. He's melting what I believe was the mic and blobbing soldier across all contacts without separating them is the same thing as cutting the cord and twisting all the wires together then stuffing it in the charge port. Stevie Wonder can solder better than this

A basic reflow station goes for $50 now. If your doing this type of repair you have no excuse not to use one anymore.

Waste of soldering wire

Very dirty work soldering is very bad

Bhai Puri duniya ko kam sikha do fir khus begar ki job kr ---bahot mahan ho aap

Disgusting soldering.

By that much soldering wire you used... You can buy hot gun

Poor solution

Type c working well??

Any recommendations for a microscope?

What liquid are you using to clean with the cotton swab?

What Liquit for cleaning?

Like your technique but the music puts me off

Maaf bang itu tapi ngerusakk komponen yang kecil gak bang, soalnyakan kepanasann

Wait I thought the leads should be pressed on the nickel blade and not one on the nickel blade and the other one on the battery as I can see you doing or my eyes are lying to me 🤔🤔🤔🤔

Nonsense.....for a small job to be done i will waste all my led and time

🎉🎉🎉🎉🎉🎉very nice

Toasted😂😂😂😂😂

This is literally the dumbest video...
1_ Why did you put solder on EVERY PART of that connector?? You have solder wick, just use that to clear the anchor points, then bridge the connector pins and remove... a LOT less hear required, and a LOT less chance of damaging the board...

If you're attempting to repair a connector, DO NOT.. ABSOLUTELY NEVER follow this person's videos as a tutorial.. holy crap that's bad.

mic may not work properly after this

Ugliest soldering technique I've ever seen.. 😳

Risky method

Nice

Use low melt solderpaste 138 C, or low melting point solder wire. It's easy, fast, cheap and professional.

Dghh

Please tell me wick name and solder name 🙏

Calicacion 0

Muy bueno 👍

Jezuz!! You already have access to the socket....Just replace the board...$10..!!!!!

wtf dude?

1. Very inefficient
2. High probability that other components were damaged
3. Takes a lot of time

Dude! Clean your soldering iron tip!!!! Get a sponge slightly damp and swipe the tip on it, it's not hard. A clean tip and a bit of fresh solder on it when you are done keeps it like new for a long time.

❤

Rule of thumb, The less lead or paste u use to get the job done, the better the result would be... 😳👍

Good luck with your total dead and destroyed phone after backing your components, ther us a, reason why they use directed heat and most possible how low it can get.

You might interfere with the ic nearby broo

couldn’t stop watching, like a train wreck. Don’t do this it will damage nearby traces and components.
Take a look at the tip of this guys iron and what terrible condition it is in and that will tell you everything.

I've been trying to replace chargin ports on LG Aristo 2 I have a heat gun and soldering iron but I don't have any low melt solder I have a flux pen if that helps I haven't tried using the flux One board I got it so messed up I can no longer see the pins I'm lost on that one Another board I did it with the heat gun at a glance it looks at least not a mess but the pins don't really seem to be connected The way I messed up the other one was trying to connect the pins A glob of solder got on there and then I had a struggle trying to remove it then I took the port back off and find that I can no longer find the pins What a mess Replacing charging ports isn't easy I think maybe I should stop trying until I get some low melt solder? I still haven't gotten the technique for this down

F it, I'll just throw it away.

What is that long brown thing you used to clear the led left off the board ?

Serviço horrível 🙈🙈🙈