Creality Ender 5 S1 Review, Setup Guide and Comparison With Original Creality Ender 5!

Hey! Thanks for the video. Im completely new to 3D printing and got this printer. Im trying to understand and setting up some profiles.
What speed do you usually print in? When doing a fine profile and just a standard one(faster)?
Print speed?
Infill speed?
outer wall speed?
support speed?
travel speed?
Also when i print the boat that comes on the memory card the filament is blank on the finished product. When i print with the standard profile in creality slicer (0,2mm layer height) the filament gets matte.. Any idea what that can be to cause this?

Hey this may be a dumb question, but I just got the 3d printer, I heated the nozzle but the filament refuses to feed, I even cut it and did the usual poking around for the right angle, even tried using the thin metal needle and nothing goes down

IS THIS UNIT PRETTY LOUD? OR IS IT QUIET?

Me who build it a few months ago and have done countless prints on it just realise it the screws are different lengths for the print bed💀

Fair play, engaged I feel. Thanks for sharing slicer config. Big help to someone new at this.

hello, I downloaded your profile to test it, and seen that you have a retraction of 1 to 30 mm/s, after printing a retraction test, it is not even close to a good print, apart from the fact that you have the upper layers to

This vs Sovol SV06 plus. Which one is better?
Thanks in advance!

This video was exactly what I needed to get up and running with confidence. Appreciated the step by steps and tips throughout the video

I have a problem with the leveling. The Z height (bed and nozzle gap) becomes larger as the nozzle moves in Y axis direction (from 0 mm to 220 mm). Have you found this problem?

I have one with the z switch why is that

Two thumbs up! You are incredibly articulate and precise with your comments. Thank you for posting

Thank you so much for making this video it’s the best😂. I almost smash mine with a bat and throw it away haha

What is the name of that pencil screwdriver you used in this video and where can I pick one up?

Thanks! This video helped me get started very quickly!!

I just received my new Ender 5 S1. Came across this video after building my printer and loved the way you demonstrated how to get started, especially leveling the bed. I watched several other videos before I reached yours and they weren't nearly as good in the startup and first print demonstration. THANK YOU!!! I ordered my printer directly from Creality along with the Sonic Pad. Haven't installed the pad yet but I'm excited to do that next. I'll check your channel to see if you've covered the Sonic Pad setup. Considering buying the PEI plate from your website.

Where is your filament change video?

I have this with sonicpad and have yet to get it to print. This printer constantly says out of print area, and it doesn't matter where it is on the platform. I get no help from Creality. Any suggestion from anyone. I think it is going to make one expensive target for my shotgun!

Hi, thanks for the video! When I turned on my device, the backlight on the touch screen lights up but there is no display for me to interact with. Any advice?

I spent hours on leveling but the middle is everytime higher than the corners 😒 and the autolevel doesnt compare the problem. Every print in the middle is too close to the nozzle. Every print around the middle is a mid-air fail... do you have a tip?

The video references a link to another for your spool holder fix, but didn't see the link.

I lined up the Ender 5 S1, the Flashforge Adventurer 4, and the Prusa i3... after a week of heavy research and after watching this video, I decided that the Ender 5 S1 will be the first 3d printer that I own - I actually ordered it while the last few minutes of this video were playing in the background. Thank's for the complete breakdown and honest review.

Great video! i used this to set up my Ender 5 s1 very helpful. Will there be a sonic pad video on CE5 s1??

I would love a comparison between this and the Ender 7-post modding. I'm really curious about your opinions on the Ender 5S1 cantilever. The only thing I feel like this printer doesn't have is dual z axis, although I don't own one and can't speak to whether it is necessary.

Lowering the retraction speed around 25 or 30mm/s with .8 to 1mm retraction will likely fix the whisping.

Thanks for very good rewiew!!!

What type of materials can be used with it?

Can you share the settings? I print with 120mm\s , 0.8mm retraction, 30mmn/s retraction speed, PLA at 205/60, but i always get clog and can't print :/

I've watch a ton of videos about this machine but for me this gave me the information I wanted. You showed plenty of finished prints in good close up and that's what I wanted to see. The prints look good. The Info about the print plate was excellent and I will order that at the same time. I have been tossing up between this and the Bambu Lab X1C but for me in NZ its about $1000.00 less for this and the prints look kinda the same. Good video. Thanks.

My ender 5s1 does not have a z limit switch or wiring fot it. I noted this was missing in creality assembly video as well. Any idea why I would not have that?

Great video, Cool Channel...I love my Ender 5Pro+ ;-p

I flashed Klipper on the 5 S1, and was able to get rid of the stringing. I don't know why I (we) had such a hard time with the stringing using the original firmware. Have it very reliably running at 120 with great results. Nice Review!