Weather pack (waterproof) Connectors Assembly without using special tools

Now we just need to see how to remove the wires.

great, the only tricky part is to insert the pins into the housings such that they properly latch. but you hear the ‚click‘ when they do (in this video, the ventilator is quite loud). I‘ve used just over twenty of these connectors when I restored my BMW Isetta.

Not for the faint hearted. Once you figure it out you can do these pretty fast. Thanks for the video, I would have never figured this out. A big Thank You !!!!!

Misleading thumbnail, by which I couldn't concentrate on the video because of that monster

Why is your thumb nail so long?...lol

is this good for automotive wiring?

Hey buddy, I have an outboard motor boat I have a sensor I pulled it apart. A orange thing fell into the water some kind of rubber thing I’m going to pick it up at the Marine store. Can I put the rubber thing back on the same way you were putting this rubber thing on your wire

Cut your nails

What size were these wires and molex pins

$17 for an ISWISS and you can crimp those tin parts like a boss. I like these connectors... the Deutsch ones a bit pricey in comparison. NICE!

Bro this wire voltage capacity?

this is exactly what I needed to know! Thank you for making this video!

how do you depin these?

Parabéns pelo vídeo nota 10

No one noticed his ugly thumb nails 🤢y they do long

That’s not Weather-Pack, it is a AMP Superseal.

So macht man das nicht!

Thanks very much!

Salamat sir!

Great Video Thank You

Link plz

Trim those damned nails!! Thanks for the video though. 🍻

Pano baklasin to boss if ever? Madali ikabit mahirap siguro to i baklasin if ever gsto palitan at ireuse

can the connectors be reused?

EXCELLENT VIDEO!! THANK YOU!!

Thank you this is a God sent video I was looking for help rewiring my Scooter and I bought those exact connectors

What tool you need ?

Watching this because I'm trying to de-pin one of these

Disgusting nails

The smaller plastic piece seems to fit perfectly onto my mazda spark plug ignition coils! Will they stand up to the current?

Thank you

How do you remove the pins is what I'm looking for. Looks the same as what I have

Are those just regular wire crimps that have that hook like piece you can clamp the pin parts down with?

I fished mine out of the garbage after I saw this video. The instructions (single paper) were terrible and for the life of me I could not get them to work. This saved the day. Thanks

Holy fingernails

Where to buy trim pin & socket

THANK YOU!! These things should come with instructions

This video was as useful as tits on a bull. slow it down, get rid of the shakes (have a drink of whiskey) and better resolution.

Cut your fingernails, my dude...

What's the name of what he's using in the video?

Just thought I'd share my experience in case anyone else had trouble with these: I couldn't for the life of me get the wires to lock on the male-end (aka the longer side). Went through about 2 sets of connectors and a bunch of wire before I figured it out: needle-nose pliers. I had to grip the crimped connector through the other end and pull on it relatively hard to get it to lock since I had no luck in just trying to push it through by pushing on the wire itself. So definitely try to pull-method if your wire isn't locking into place on the male-end.

All tsilaight should be installed with these

Bought a sack of these and almost gave up on them until I found your awesome video thanks much!

how to removal the male contact conector?

thank you very much,big respect from indonesia 🙏🙏

How do you identify which type of terminal to crimp on the wire to enter the bushing terminal connector? I have a 220 545 52 28 pin bushing connector that ultimately needs to hook up to a p04602670AE heated seat module. I can not identify the terminal that is needed to save my life and no one seems to know either. A 2.8mm spade connector is close to the size but too small. I think it's 3mm. If not 3.5mm and rectangle shaped to go over the male end

Thank you for sharing

I think the correct way is to put the red part only in the end.

how wil i T off from this conectors? for example i have wire coming from battery and want to conect 2 lights .. can i joint red on red black on black a put it in one conector ?

How would you unpin each point?