Комментарии:
Didn't with mine, all broke. I'm trying to ream holes bigger, very gently
ОтветитьDoesn't work on chip beads
ОтветитьGià lo facevo io non è una novità
ОтветитьNext up, use a Lark's Head rather than a loop so the cotton's easily removable. Put the thicker cord across both cottons, so there's a loop in the cotton on both sides, then pass the needle through the other loop, catching the cord between. When done, reverse the needle from the loop.
ОтветитьI had to fast forward a ton 😂 vid is so damned slow it was annoying
ОтветитьPretty sure you could have done that without a needle
ОтветитьCan you please send me the link of this elastic thread???
ОтветитьThank you so much for sharing this kind of information 😊 from Portugal 🇵🇹 😊
Ответитьtried this a number of times and I can not get it to work. Maybe I am doing something wrong.
ОтветитьA variation on the old wire needle threaders. So clever. Thanks. 👏
ОтветитьThe easier way would be to wind the clear wire string around one end of the cord and part of the wire string to secure it and off at the cord tip which would make the cord come to a point at the tip seem narrower then thread the beads on n the wire string and pull them up the cord. It works well and doesn't make it as difficult as pulling them over doubled cord.
ОтветитьI'd do a little bit of glue on the top of the cord and roll it a bit. Let it dry a few minutes. Then it went through the whole of the pearl. If not - nothing would work.
ОтветитьThis is AWESOME! Thank you!
ОтветитьLIAR
ОтветитьWow can't wait to try this thx a bunch!!!
ОтветитьThank you 😍 🪡
ОтветитьI'd end up stabbing the needle in my palm somehow
ОтветитьThis is really a game changer for bead crafters! The first time I tried this I was so excited until I realize that my needle was too fat for the bead hole😂😂 So anyone trying this, make sure your needle fits through the bead first!😁👍 To the person in the video, Thank You! for having such nice clean fingernails. Ive seen too many craft videos lately with close ups of dirty fingernails and it was so distracting and off-putting.
ОтветитьGreat tip!
ОтветитьMuito obrigada pela ideia genial Deus abençoe e proteja sempre amei
ОтветитьSong please? ❤
ОтветитьDica joia linda pesa charmosa 😍 escrita sucesso ❤
ОтветитьThank you.
Ответитьwhat about with alphabet beads through
ОтветитьVery good 👍
ОтветитьTysm!🥹💗✨
ОтветитьThanks. Very good tip for when hole is a little tight. 😊
ОтветитьУжжас как медленно!!!😢
ОтветитьNeat trick I'll have to try it
ОтветитьI normally melt the cord and roll it between my fingers till its thinned out with a sharp point works well for me but guess it depends on the type of cord you use too.
ОтветитьThis does NOT work all the time! If the cord is too large in diameter than the bead hole...plus by doing you are doubling the cord diameter. If the cord ends are loose cut at about 45 degree angle and dip 2-3 cm. In Super Glue an let dry. It makes the end of the cord stiff , then use kindi like a needle. Something I just brainstormed up ...but has helped a lot.
ОтветитьThat's more of a frayed end problem then a thick cord problem
ОтветитьWhat kind of cord to buy?
ОтветитьCracked my cheap beads 😩🤷🏼♀️🤣
ОтветитьEh who is daft enough to want to put this size cord into that size hole. Just use thinner thread 🙈
Ответитьwhat a nonsense, how is a double strand supposed to go through the hole if even a single strand does not fit…only works with soft elastic strand which gives way, but not with sturdy material….alas what you showed the world is just how to make a threading tool, available in every dollar store or buy in china, you get 100 pcs for a dollar, nothing genius about this
ОтветитьGenial truck.
Gracias eso si es tutorial.
Clarìsimo, fácil y Breve..
Desde Nicaragua 🇳🇮 C.A Bendiciones.
The bead won't go over the eye of the needle
ОтветитьQQQQQQQQQQQQQQQQQQQQQQ DICA MARAVILHOSA !!!!!!!!!!! 28/10/23
ОтветитьVery interesting ❤
ОтветитьJ'ai trouvé,elle a changé de perles😂
Ответитьnice .great job
ОтветитьI have little hunks of beeswax that I coat the end with to stiffen it and coax it to a fine point to go through the hole.
ОтветитьCould you drag this video out any longer?
ОтветитьYou can just use a piece of wire fold into half, I recommend flexible wire. Then you don’t need to due with the thread every time, you can reuse the wire again and again, and it’s much stronger than a thread which you might break it when pulling it too hard.
Ответитьİpliğin ucu yakılır.Öyle boncuklar dizilir.
ОтветитьThis is a great idea but kind of confusing. If the thick cord wouldn't go through the bead the first time, how does it go through the second time when the cord is doubled?
ОтветитьOrrr you can just use a needle to poke in the hole
ОтветитьThank you ❤
Ответить