Тэги:
#accelerator_pedal_position_sensor #app_sensor #drive_by_wire #drive_by_wire_system #car_drive_by_wire #drive_by_wire_help #p2122 #p2123 #p2127 #p2128 #p2138 #app_failure_symptoms #app_sensor_acura_tl #app_sensor_testing #app_sensor_honda #Testing_Accelerator #Testing_Accelerator_Pedal_Position_Sensors_in_a_very_professional_way #check_engine_light #accelerator_pedal_position_sensor_voltage #weak_acceleration #reduced_power_mode #gas_pedal_sensor #throttle_position_sensorКомментарии:
One of the stupidest videos without instructions thanks Man I can sure read ur thoughts. 😅
ОтветитьUseless to anyone who isn't a mechanic
ОтветитьUse your words
Ответитьacceleration pedal is measured with rehostate resistance increase or decrease resistance the number of resistance tell the cpm
where the pedal is if voltage is going through increase or decrease voltage. depending on the manufactures ingeneer.
Nice😎👍
Ответитьwhy there're two 5v pins?
Ответитьje comprends rien a ta présentation quel plot quel fil ?? fais moi un dessin ce sera plus simple !
ОтветитьCat got your tongue?
ОтветитьPlease I need an electrical diagram
Ответитьthank you - I got some crocodile clips but I dnt have the proper ones like you do with insulation but will see what I can do ( my car does not accelereate at all and the mechanic says it is the diesel pump but im thnking that does not sound right at all ( I mean if the pump was faulty it should atleast rev a little )
ОтветитьWhat pedal is this? Out of a toyota?
ОтветитьThanks you very much..amazing simple but effective and helping us all learn out here..
ОтветитьHow the hell do you work with those big gloves on
ОтветитьSo my pedal doesn't accelerate until about... 1" depression.
It's always been that way though. and you only notice it after driving another machine. Sensors are everywhere these days though.
Thanks
ОтветитьSar kuch to bolo ge te samje me aay ga sab logoko
ОтветитьVery poor video. You can't see what your connecting
ОтветитьAwesome
ОтветитьGoud boss
ОтветитьI really love this
ОтветитьU could explain what the heck u r doing and what's going on.
ОтветитьYou should be talking to explain what you do and what the right voltage should be read,by the way thank you .
Ответитьit's not clear of the pins that you are connecting to, and is this a faulty pedal
ОтветитьIncrease the slow
ОтветитьHow to install it
ОтветитьVm in Multimeter in the video is showing Voltage??? @JAMS04
ОтветитьGood video showing how the APP sensors work. However, the test itseft doesn't measure the voltage difference correlation between sensor 1 and 2 which is what actually the pcm is looking at to determine if the pedal is working properly or not.
ОтветитьGood 👍 Boss
ОтветитьThis pedal work like drill mosfet switch 😏
ОтветитьWhich company throttle is this?
ОтветитьThis good accelator or bad.
ОтветитьWhy couldn't you use ohms to test instead of adding a 5v signal
ОтветитьGood usefull video
ОтветитьOnly 4 knob connected plz explain
ОтветитьVery good video, one can use the Mobile phone charger, modify it to get 5V for testing. Just need to find out the pins. Thank You. All the way from Maputo/Mozambique
Ответить