Setup of Leadshine HBS507 Closed Loop or Hybrid Servo Step Driver

Greeting. I have the same problem on my hybrid stepper motors. Hbs57 driver and hbs86. It locks the engine and cannot move. On the driver, the parameters are set to 3200 by default. Do you need to change something there or should I do as you did in the video?

thank you

How much take it to connect?

Can you add this to an ebay co2 laser cutter?

How long does it need to connect? I am stuck at that point and i am waiting for 5 minutes and nothing happens. What i am doing wrong

Thanks Martin, will search for and download. The 232 cable is another that is needed

Hi there!Maybe you can help me out with something...I am at the final step of building an electronic leadscrew...i use the same closed loop hybrid steper motor but after connecting everything the motor does not move at all....it is the clough42 project but i used this motor and stepper.....maybe y0u can help me?

That would be a true servo if it is 3 phase. Stepper motors are 2 phase the ones they sell to the west are stepper type 2 phase and use 4 wires which are called hybrids.

What kind of controler do you used for BSH 507 driver motor

Franco now has the software on his site! (Drop box download from one of his videos)

What's the rpm speed it starts do lose torque? If the drive falls in alarm, how can I recover it?

hello friend this HBS507 Closed Loop or Hybrid Servo Step Driver can we operate it through Delta Plc DVP mode? please Do you have link please sen me.

Hi Martin,
another question:
what are the settings you used for the serial port besides the baud rate of 38400 ? ( parority , stop bits etc ? )
thanks
Stephan

Hello Martin ,
Thanks a lot for your video .
I am referring to your Answer to Astronobob .
I downloaded the software as per your link to your dropbox.
I also own 3 Servo with hbs507 drivers for my cnc mill. Now i have to make some Changes in the Driver , but i am not able to make a connection to it. I get following messages ." Unknonwn drive " Connection failed. The Baud rate is correct .
I made my cable as per leadshine diagram , using a USB to RS232 adaptor which i surerely know to work properly .
I even tried to switchTX and RX with no avail..... so i am still stuck !
Any sugestions ? could you please upload to your dropbox the original chinese software ? my last ( ? ) hope to get the things going .It would be sad to throw away the servo drivers.... in the default settings there are not suitable for my project.
Sincerely . Greetings from Switzerland

Stephan

Hello, any chance you still have those software files for tuning the drive? Can't find them anywhere

Excellent video. Thank you very much!

Hi bro . Pls tell me part number of encoder cable . If you make it . Pls share me diagram electric of cable . Thanks bro very much

Hello friend, congratulations on your video, could not you make a video showing how to configure the micro steps? thank you.

Thabks a lot!! It's been realy helpful.

Hello Martin, great Video and now I will order the HBS507 but can you me tell what you use to conect it for a controler was the PoKeys57CNC or another? I will use the HBS507 with the mach3 Software, thanks and best regards Adi

I have been wrestling with whether to try these or the Leadshine Nema 23 Servo(not hybrid stepper) model BLM57180 with the ACS606 controller. I want very smooth action to reduce resonance for improved side mill finish on a heavily modified G0704/PM20. Going for linear rails, C3Z ballscrews and the smoothest spindle/motor setup I can find as finish is key over speed.

Can conect to arduino?

the link Works, but you must erase the Word Thanks at the end.

thanks great details ,,,what is differnce to connecting to Arduino with stepper drive ? is it same connections step and dir,5V

hi martin, why i got an error message on motor tuning , position error (pulses)

hello

the programming it is recorded in the driver, if disconnect the cable (RS232) that goes to the computer?

thanks

Hi, how to communicate two driver, like 1 axis using 2 motor, if 1 motor wont move and the other motor have to stop also, to prevent from twisting the gantry..

hi, super Tema , ich habe 3kG Schrittmotoren mit einer normalen H-Brige , leadschein macht die Driver als Hybrid , sind die Dann auch für Ac Motoren 3 Draht ?
sind Die Ac_Motoren leiser ?
wie ist der Drehmoment?
wie ist haltemoment?
kann die Software benutzt werden für die Anpassung des Encoder ? Anderen Ac Motor vverwendbar ? mfg

hi please do you have any idea of how i can control this servo drive with my plc

hi martin,, mine is keep appear a position error,, why is that,, and what is the best setting..

Dear Martin, For CNC or 3D printer, replace old nema stepper motor and driver with ES-D driver and step servo motors, then closed loop system is done? or need to modify some firmware or software settings?

I have found an English version of Protuner that actually works! Some comunication problems -> the port closes on it's own but it works.

Hello guys, can you help me, I want connect driver to computer by USB to COM, But the software warning communication fail.
I Try to again but still fail :(

Hi Martin,
This video is extremely valuable, but i don't know, How connect HBS 507 to Computer ?by what ? do you give me diagram ?
Thanks.

can i use normal steppermotor whit 1000 P/r encoder?

hi , thank you for the good info , i have a question ..
is the rotational accuracy 1000 encoder steps or the 1.2 degrees ?

Hello, Iam looking for a software for a HBS86H driver but I don't find it on the Leadshine website. Do you know where to find it ?

Is it possible to use this leadhine closed loop servo with an arduino&grbl?

Hi,
I've tried to look up the model HBS507 on leadshine website but it's no where to be found. I thought this was kinda strange.... has it been discontinued? All I see on their website are the ES-D Series for DC voltage (which looks very much similar to the HBS507). Does anyone know why?

Martin I have a question, in your earlier videos you have a fairly decent looking Openbuilds OX but you seem to have changed to using an X-carve and recycled the 8020 to make a controller box. What was the reason for this?

Just a tip that you can get rid of these junk ??? question mark things by installing a Chinese Language Pack in your windows.

Hi
oh that's a big driver
have you work with 3d digitzer using a touch probe on the xcarve cnc ?