HOW TO REBUILD VIVARO MOVANO TRAFFIC VITO PF6 6 SPEED GEARBOX

Where do you get your bearing kits from? Any recommendations?

Can you let me know where you got this work done. I need the same done to my gearbox on my van.?

I did`t see thickness of adjusting rings regulation process. its not compleatly repair. Колхозный ремонт !

Hi, i just open my pf6 050 on a vivaro 2015 1.6 120hp with 138000km. Also my frend has a 2015 trafic 1.6 90hp with 124000km and has a noisy gearbox. I think the pf6 is a weak gearbox.

Fantastic to watch, thank you so much for this. Silly question but is it only bearings and seals that are replaced when a gearbox is reconned ? What's the situation if a synchro ring is damaged or a gear itself ? Can you buy those bits ?

Did you make any adjustments on it ?

My Trafic gearbox has just gone kaput, dudes you are all legends, thanks very much.

Great vid. I've got a oil leak from the selector shaft that moves the stick from side to side. Anyone know if it's a seal that can be replaced with box in situ or is ait an internal (gearbox out and apart) job??

What was the cause of the tight lever when you tried to refit the casing first time round?

How would you tell which shim goes where. One is slightly thicker than the other by 0.25mm

Do you have any video about Pk6 Gearbox as well?

Very skilled work!

I raced BMWs for years and every three years the bearings in the gearbox would start to whine. They were originally filled with ATF, but if you used lightweight gear oil they lasted longer. Off to the breakers to source a used one. I tried to rebuild one once, but could never find a source for the bearings since ZF didn't sell them separately. I'm sure it would have been possible, but I didn't have the knowledge to source them. Watching this, he makes it look pretty easy, but imagine all the ways you could mess up during that job! Well done.

Pk box was shite and the pf ain't much better

There will always be a place for good engineers, very interesting, thanks Rob.

Great vid, but surely a blind bearing puller ( £30 ) and a press would be a little more sympathetic to the gearbox casing rather than a massive lump hammer....😩
And a parts tray to keep things in order

Someone once told me these gearboxes are derived from a Renault Laguna and can't cope with the torque? Mine went at 80k now needs doing again at 120k!

Amazing how powerful the latest impact drivers are today Great work very interesting

Appreciate you doing this Rob

I'd be happier if the bearing seats were pressed in rather than hammered into place ...

I just took a Renault TL4 box apart (which seems to look identical) to replace 3rd and 4th gear synchros and fit a blackline LSD. Was good fun, first time I've done anything with a box other than remove to do clutch etc. Input shaft top nut was fun!

🚗👍

Great vid..surely chris can rebuild a gearbox👨‍🔧👨‍🔧

very very impressed with his work and his own made tools . A true problem solver .

Not a bit of me. 🤷‍♂️

Really enjoyed this Video!
Would have been Better with a Little more Chris and a Little Less Rob 🤣🤣🤣

Very handy for our group many thanks

Fascinating. Amazing how easy he makes it look, but I’m sure he’s had lots of practice. Enjoyed the video over my tea this morning.

That was a Fantastic Video to watch Rob thanks for showing all off that video.

A dying trade but so good to see a young lad with the knowledge and enthusiasm to strip out, repair, and importantly do it correctly

Here was I expected a video on possibly the camper van, but no yet another great video showing complete job thanks really appreciate it. Thanks again guys top content 👌

great video Rob,entertaining for us and also saved you money,as did your quickie on the Peugot coupe where you done a tensioner replacement and saved cost of new engine,this helped another channel man that I watch with his citroen and he gave you a mention (chops garage)

well done that man

Josh is sooo cool! What a talented guy! Josh you da man 👍👍

Great video and fascinating to watch, I wouldn't have the patience to do it

brilliant vid ,good job Josh 👍

Great video...Nice one Josh, loved that...👍👍👍

Josh, Top bloke. Enjoyed that. 👍

I didn't click the dislike because i like SRUK. I did not like this video because it was to long. Rob and Chris put out 3 videos a week and they are short because they time-lapse all the hard work. Do we want 39 minutes of Josh building a gearbox or do we want a 1 hour video of Rob and Chris installing it?

Brilliant. After putting away horses and chickens at two locations, this was an interesting transition back to a brand of reality I seldom enjoy. Thanks so much.

wat expertise in this vidio.wat a good chap he is.

I've got a vivaro rob on a 57 plate and every now and again it anuissance to get into second but saying that it has covered 165,000 miles I drop the oil every 10 thousand on the engine and filter you know what mate I've had new transits and they have given me more grief than this one has I'll keep this until something major goes like before I part with it... Loved the footage here... keep it rolling mate! 👍

Good job! I am surprised a torque wrench wasn’t used though, particularly on the reverse gear bolts.

Good
🇬🇧😐

Say what you like about mechanics they can get a bum deal from a few but there bloody clever people , there’s a lot mechanical knowledge going on here it’s far from a bolt on and off job ….hats of you dude a very interesting vid indeed thanks for sharing 👌👍

Handy with the hot spanner too

It seems that a thorough wash would be the first step- it's a lot easier to pressure wash the main housing and get all that road grit off when it's still one sealed up unit.

Thanks for posting this up, I have that gearbox in my van and it's fascinating to see how it all goes together.

Excellent video,, Josh is pretty knowledgeable like Chris and not afraid to talk us through the process,, hopefully more of these on different capacities in the future 👌,

👍