Top 18 Drill Bits You Need In Workshop

a lot of them are not drill bits

Fühle mich bei diesen Darbietungen richtig "heimisch".
Es ist wohltuend diesen aussergewöhnlichen Menschen bei ihrer geistvollen und geschickten Tätigkeit über die schulter zu blicken! Ich bedanke mich bei allen von ihnen für dieses Vergnügen.

I did look for invisible links but did like the wood bits being used to cut metal

Only Americans use Philips head screws. Real men use Robertson head screws.

dude this is terrible. at least use a vise or something to hold your workpiece down, don't teach people how to get themselves hurt. also drop the sh*tty accu tools and use a real drill for drilling holes, you get an arthritis or some sh*t.

j'ai des difficultés à percer l'INOX quel foret utiliser .Merci

And the real world those screw-outs do not work ever especially on Old corroded rotted screws that are frozen into wood or metal. In a shop where you just put it in there yeah it'll come right out because it was just freshly done but five 10 years later never going to come out. You need locking pliers to grab onto the outside of edges of the screw and then slowly reverse it out

TERRIBLE SELECTION OF BITS.

Seriously man, use hand protection or a good vise. Damn 😰

Where did you get the small red magnetic pieces for screw bit

Hmm! Most of them are parkside bits!

It wasn't vwry far into the video I had a "Huh" monent...hence the like

Lhaa pake kayu yg emfuuk...coba pake kayu jati , bengkirai,

What a bunch of miseries in the comments. Learned a lot, thanks

Links to the tools would be great

The thumbnail picture is an endmill, and is not a drill.
Just sayin...

There may be two out of the whole bunch you need. The rest are doubtful in my opinion.

lol after you deburred the all thread you threaded it on to the side you didnt even deburr lol

I once tried using a circle cutter shown at the end. They were slipping out while turning at high speed. Could realize that only because the lines on the wood were growing wider. If not for it I would have been struck by them. I stopped it and tightened them further. Still the same problem. However I tightened them it was not sufficient. So scared of using them.

Thanks bro , I was not aware of all these drill bits, thanks again.

So nothing new at all! I've had all these bits for years and some for decades. The only thing I don't have is the buffer pads. But good video to show people what good to have though!

Merci beaucoup pour la vidéo

Gee, did you get a new toy and wanted to share what you don't know? You missed the whole idea of a Forstner bit. Yes, you can cut a hole through a piece of thick stock. But the real feature is that you can cut a flat bottom hole into a piece of wood. Oh, and the tools that follow the Forstner non-demo are called nut drivers, not countersunk wood drills. Sheesh!

Thanks. Interesting. But please : USE GLOWS, above all with the cone drill :P

So the thumbnail was click bait..... Thumbs Down.

Some pretty cool bits I've never seen before though.

These Bosch drills remind me of drills that old ladies buy from tv ads.

ни один профессионал, не будет пользоваться этим.

Never once have those damaged screw extractors ever worked.

All I'm seeing is a pepsi commercial!

All that effort to deburr and round edge of threaded bar then puts nut on wrong end 🤦‍♂️

If it's not a carbide tipped holesaw it's not worth owning

Sorry but this is the most boring unnecessary video I was falling asleep on the third hole , it's amazing that a drill "Drills" !

You missed Square hole drilling ?

Going to wear out that screw extractor really quick pre-drilling in forward instead of reverse like they are made to do.

In the two decades I spent as a machinist, I don't think I nor anyone I worked with would show an 8 fluted end mill and label it as a drill.

You are not supposed to use water with carbide. Literally says this in your operation manual.

В чём смысл видео я не пойму, это всё уже давно есть в продаже, заняться нечем, иди поработай с пользой.

Apparently a wood plug cutter and countersink are vitally important since you show both twice. I think the first demonstration covered it, but if you didn't catch the first one, thank goodness you showed the exact same thing again.

It would be nice if you gave a place to get all these items

A very useful support tool for carpentry work.

You would be better to clap things down or it will fly out of your hands

Es interesante lo que hacen las personas mudas, siempre he pensado que los que tienen sentidos limitados, son los mas creativos, felicidades a todos los mudos, deberían de tener otra persona para explicar a detalle para que el video sea mas completo, aún asi, es buen video.

👍🏾

Nice demonstration,👌💐

Good job

Wow amazing beautiful idea 👌✌️ thanks my friend 👍👍👍