SUPER Clean intake valves with this simple trick...

I not have problem, I have port F.I. aI I had D.I. disconnect PCV.

Ha ha. If you exercise your engine correctly ie, full range acceleration and long drives this problem will not happen. Never had this problem in over 60 years as a mechanic.

it is not trick it is service in shop

Thats impressive

Can this technique cause issues with valve sleeve and valve stems’ errosion due to the micro sand particles being trapped in the gap after this process and then acting as abrasive material? Valve seals are also a concern.

Great idea. I believe I could build an adapter like that out of a nice chunk of hardwood.

amazing! A good blast of air from the spark plug well as your rotating the valves open would be my final step.

c'est nul, ce procédé ne nettoie pas le siege de soupape, donc aucun changement de puissance, de compression et de consomation.

My trick is to drive port injected cars.

Con las modificaciones,es el mejor limpiador q he visto🔫💪🏼👌🏼

Why not just add a nitrous system 🤷🏾‍♂️

You wouldn't notice the difference between dirty or clean valves. I've tested it many times...

...урн все херня лийте якісне пальне , мастило міняйте через 10к дайте двигуну прогрітися до робочої температури і все буде ок ці забруднення наслідок коротких поїздок

Bastava un pulitore detergente aspirazione...senza smontare tutto 😂😂

Hi mate does that shot blaster realy work good video thanks for sharing that information very useful 😊

My trick is not buying direct injection cars.

The voice over is woeful. AI sounds like a monotone sleep inducing.....zzzzz

Great vid, I have the same gun and setup (you can get a long straight extension from spray gun kits that fit a 1/4" connector). I always tape up the ports I have done and the open valve port, this stops any random shell blow out getting into them. Baking soda also works, it's cheaper but not as good as the walnut shell.

After performing this procedure it is good idea to install an oil catch can, then you may not need to do this procedure for many tens of thousands of KM'S if at all.

What a nice way to destroy your pistons

I've been wanting to do this for a while on my Ford Transit. But wasn't sure of the effect, nor the difficulty level. I also wasn't sure how much of a difference it would make.
You answered a lot of those questions for me. This is definitely the best way to deal with the EGR system.
Thanks for posting!

Put it in the highway and drive it as it was stolen, so these GDI we're designed for. Otherwise they clog Like you see here

In the past I drilled small holes in the intake manifold and inserted plastic lines to a water and alcohol 50/50 mixture in a gallon bottle and just drive normally. The vacuum would pull in the mixture cleaning the valves. Seal the plastic lines when finished. Did this once a month. Seemed to work well as the engine ran just fine.

Soo' the! Name: bei denn 2 start Bilder des Videos. Ja ich glaube das , wenn die Arbeit fachmännisch und sauber durchgeführt wird. Das der ein oder andere HP dabei herausspringt bzw im Motor bleibt.

Great video Ali. Wish I could have you take care of my ride

Do you think this coulld fix a sticky exhaust valve on a Mini One, before I have to take the head off and clean it completely?
I have a misfire on cylinder 3 and the value is stuck open with no compression.
Love your videos.

Esto es peligroso. Si por lo que sea la válvula no cierra bien, todo para adentro al cilindro.

Nicely done!

HOW MUCH damage is abrasive sand going to do after getting into the engine (in short and/or long term?). Is this not madness?

So I need to take half the engine apart to do this. I will start cleaning process after I take Community College class how to take engine apart. Then I will spend days doing the cleaning.

Hello,

That's exactly why this technique was invented, because it won't hurt if it accidentally stays in there the nutshell. It will burn in moments.
No need for high air pressure, etc.
👌🏻✌🏻

Ma che fesseria è

Brilliant video and detailed explanation of how to create the solution, many thanks for your efforts with this issue. Awaiting more good stuff like this from you!

Hi, great video!
- How many kg of walnut did you use for the for 4 intake ports?
- Which pressure in PSI was your compressor set ?
- How many minutes did you blast per intake port? (If I assume my intakes are as dirty as yours, I should blast not less than X (?) min…)

And finally: can you tell me how to make/order an adapter for Hyundai i30 1.6 L GDi 2015 (99kW) ?
🙏 Thanks!

Blasting grit into the ports??? Just NO. There will always be some left behind to drop into the cylinder, get in other places. Just pour in a bottle of injector cleaner once in a while, keeps everything cleaner.

But this doesn’t clean the actual sealing face 🤔

Load of nonsense will make no difference , valves have to be removed for cleaning, abrasive particles in engine, amatuer

Die Lösung ist die Abgasrückführung abzuschalten. Die Motorsteuerung muß Codiert werden. Dadurch werden die Ventile verschmutzt.

Super fácil vamos

Es una locura nunca vas a lograr sacar todos los granos de arena y cuando arranques el motor se van a rayar las paredes de los cilindros
Eso lo puede hacer una persona que no tiene idea
DEJEN DE HACER ESTOS TIPOS DE VIDEOS QUE ARRUINAN LOS MOTORES

Had this done to my Peugeot thp engine made a huge difference

Spray bottle of water into throttle body at idle cleans the valves. Spray until you hear the idle drop & stop. Do this over & over. Proven to work, the water turns to steam which cleans the intake.

You have SIMPLE in the title....🤨😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂






😠🤬😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😣😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂






😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂🤨🤨🤨 waste of time!

does the better one you put on the list need the modification as well?

damn the rotted pb can will do it idk...didn't that know that.. put it on the joints man that is way better but plug ground is broke tho.

😢😂

A very good job 💪👍👋

I already have that blaster i purchased from Harbor Freight. I never thought of boring out the passages. What a great Idea! Thanks!

Limpou toda a válvula menos onde precisava que é no encosto com a sede!!! Não adianta de nada

Yeah this is the very very fuc*ing simple way !!!