Комментарии:
❗Please enable subtitles in your language 🙋🏼♀ Thanks for watching 😋🤗😘
ОтветитьReally is a shit 🤢🤮🤮🤮🤮
ОтветитьDónde consigo el relleno de plástico ?.
ОтветитьI am from Brasil
ОтветитьMe gusto la idea del uso del tubo de pvc, ya que es moldeable con la pistola de calor. 👍 Aunque no se que tanto tiempo puedam resistir esas pequeñas grapas, ya que son de un material frágil.
Lo tendre presente para futuras reparaciones.
Süper bir uygulama tebrikler
ОтветитьLlámame para darte unos tips, por ibas hasta que le hechastes pega
ОтветитьGreat method, very useful. Thank you.
ОтветитьExcellent!
ОтветитьPretendo restaurar algumas partes da carenagem da minha moto. Vou experimentar essa técnica!
ОтветитьHàn ống vặn vít của đầu xe máy.
ОтветитьШпатлёвка на глянцевую поверхность не очень хорошо
ОтветитьCách tốt nhất là mua miếng decal nhựa dán lên là xong. Giống như miếng decal vải để dán vải.
ОтветитьMuchas gracias por su ayuda excelente idea, saludos desde Costa Rica.
ОтветитьUmmmmmm an epoxy stick would do that in a heartbeat. Just use an 80 grit piece of paper and get a half inch around the hole on the outside and an inch on the inside. Then knead the epoxy stick and make a pancake the size of the hole but pike a half inch thick. Then use thinner to smear the epoxy pancake onto the sanded part of the fender on both sides and shape it. Then you sand it down and block it with a nail file cut with scissors or a paint stick cut in like 1 inch pieces and use rubber cement to glue the sand paper on the pieces so you can block it with them. Do 80, then 150, then 220, then 409, then 600 and tape it and prime it with a plastic primer. Then you can use 400 and wet sand it then 600 wet sanded.
Then tape it and spray it. Blending it is a little different though. You will have a line unless you paint the whole thing or you do a j blend/ cut it in with a solvent blend method. That is when you spray a solvent on the part you paint and blend in the old qith the new. It isnt the easiest thing to do and is impossible with a 2 square inch section but i would iust paint the whole thing after scuffing it with 220 then just prime that thing and then 220 and 400 wetsanded and 600 wetsanded then spray color and then wait a few hours and use a heat gun and then put on a two part clear like spray max high gloss clear. You will have a better product. You could akip a few of the steps i suggeated but i wouldnt. Glazing putty made by 3m is good atuff for plastic in thin coats. But that fender is like $20 new and painted if you can find it. 😊
Türkiye
Ответить😐
ОтветитьRealmente es un cirujano del plástico 😮, gracias por compartir tus ideas con todos ! !, saludos desde Argentina 😎💪👍🏼🇦🇷
Ответить🎉It's a great idea!!!🎉
ОтветитьNice
ОтветитьZ czego ta biała rurka ?
ОтветитьMe parece muy práctico
Sencillo y económico
Gracias por compartir
Saludos y bendiciones desde Monterrey Nuevo León
México
Excelente trabajo mis felicitaciones desde neiva huila Colombia
ОтветитьParabéns professor nota mil pra vc, aqui é de vitória espírito santo
ОтветитьFaltou mais acabamento, mais muito bom o concerto do plástico..
ОтветитьVery clever..
ОтветитьI have a piece of plastic on the bike's front tire and I lost some of it. How do I complete disbelief?
ОтветитьSi no tienes técnica para fundir las grapas con el plástico, le puedes hechar pegamento epoxico, es más rápido y de mejor acabado.
ОтветитьWonderful
ОтветитьMuy útil gracias lo voy a poner en práctica.nuevamente gracias.
Ответитьtop 10
ОтветитьTécnica ótima, acabamento e finalização péssimos.
ОтветитьMotorun ön çamurlu kırık İstanbul’daysanız eğer yapıp video çekebilir misiniz getirsem
ОтветитьGreetings from Turkey🇹🇷
ОтветитьHarika
ОтветитьHow many watt soldering iron are you using?
ОтветитьBuen trabajo pero se nota el arreglo,para la perfección debería haber usado una imprimación primero y una lija al agua mas fina después y para terminar la pintura
ОтветитьAhoj, díky za video. Dívám se z Vídně, Rakousko. Jirka
Ответитьparabéns
Ответитьnice
Ответитьବହୁତ୍ ବଢିଆ କାମ ❤
ଓଡ଼ିଶା ରୁ ଶୁଭେଚ୍ଛା !!
Excellent idea.
ОтветитьWonderful.
ОтветитьGood idea but the finish is not enough
ОтветитьBrasil, São Paulo capital
Ответить🇵🇭 thanks... 😊
ОтветитьMuito bom ótimo aplauso
ОтветитьExcelente trabajo, saludos.
ОтветитьMás fácil cortar el PVC c 1 regla y el cúter
Ответить