Комментарии:
Excelent
ОтветитьHas me stuffed why they say to screw the sheets down in the valley and not the peak, the rubber washer under the screw heads dont last for ever and always some get damaged while the screw is being screwed down.
ОтветитьI can not find a video that shows in detail how to properly close a metal valley when a lower ridge runs into the slope of a higher perpendicular ridge roof section. The mystery is how to seal the very top where the valleys intersect.
Ответитьทำได้แค่ในคอมทำจริงมึงจะขึ้นมุงอย่างไง55555
ОтветитьExcelent method
ОтветитьZ_
ОтветитьLet me put my caulk in it
ОтветитьThis only stops rains, not hurricanes, I have been doing forensic architecture for the DoD, and I see them fail every time a hurricane passes through a base. After that, any heavy rain fall the interior of the building will be cover in pools of water or leak will came from the failure of the neoprene seals.
ОтветитьNo purlins?
ОтветитьWe tore down a 70 yr old commercial chicken house having a metal "5 V groove" metal roof. It had the old metal roof nails...all placed at the top of the V grooves...not in the valleys. The wooden structure was in remarkably good condition with no rotting. Placing fasteners in valleys is a no-no.
I am wondering if an air gap underneath of approximately 3/4" would help cooling of the roof?
Well detailed thanks
ОтветитьYou have some really awesome products in your part of the world
ОтветитьThis diagram has you cut some metal off to fit inside the first piece of flashing,but then it says to put caulking on it, then slide it under the first piece! This is physically impossible to have the second peice slide under the first yet have the trimmed off peice fit inside the outside crimped edge!
It would have to go on top of the first peice and caulking would be applied to the first peice of eves flashing!
I was sold a system that costs me more,and another company just uses drip edge for the edging,same as for a shingles roof.
The point is,if you watch different videos on how to install a steel roof,if your paying attention you should notice there's 2 ways to do it!
A 3rd is just not bother with eves flashing and the hardware you don't need,as your evestrough covers most of the wood under the roof as well as metal or vinyl soffit put under the overhang !
1inch screws are never long enough should be 2or2@1/2 inches I have a friend with a pole garage over time freeze and thaw and wind worked the ends of the panels loose and caused leaks we replaced the screws with longer ones to fix the problem just a thought
Ответить好清楚...讚
ОтветитьVerry good👍, thank's for vidios, verry important for me,
ОтветитьI agree leaks happen placing screws in valleys.
Ответить?!
!?
Nice👍👍
ОтветитьCan diabetes be cured by walking?
ОтветитьIf you are screwing right through, over time couldn't it leak at those screw holes.
Ответить👍🙂
Ответитьtnx.
Ответить顺序,条理清晰✨🌟🔰📜
ОтветитьHow about no fastener
Ответить👌👌
Ответитьthat is a lot of holes to drill in your roof... that's hundreds of places its gonna leak
ОтветитьThanks for this detailed excellent video. It was very clear and concise with no fluff or wasted time. THUMBS UP for sure!
ОтветитьБлагодарю! Отличная видеоинструкция по монтажу металлопрофиля, инструкция как должно быть! 🙂👍👍👍🤝
ОтветитьGreat video....
ОтветитьYour screw is in the very wrong location lol,,,,
ОтветитьNope, been roofing for over 30 years, and not one leaky roof.
You're doing it wrong.
On the drip edge you are supposed to notch the drip on the first piece that is installed, caulk that one then the next open the hem put it in position then roll it into place making it easier and you wont plow the caulking.
ОтветитьCalling bs on screwing into the valley. Get out of your offices and actually talk to and check out the homes of ppl whose roofs have leaked and caused extensive damage.
ОтветитьVery well done, so i subscribed.
ОтветитьThe uphill flashing install was very unclear. How does the panel magically go from a 120° bend to perfectly flat? 🤔🤔🤔
ОтветитьChimney flashing
ОтветитьWrong in multiple ways bro , sorry 👎
ОтветитьNot screws. Flat leak water
ОтветитьAre the stitch screw in the high spots of the panels ,actually suppose to screw into the wood or do they just catch the metal roofing panels and poly closure?
ОтветитьNothing is better than a roof riddled with screws and completely dependent on rubber washers, foan closures, and caulk tape.
"Gee, why does my roof leak?!?"
I like ASC roofing, but I've only done a couple with these type panels. I prefer their Design Span standing seam, but, it is more expensive.
ОтветитьON THE ROOF PUT THE SCREWS ON THE IBR RIBS. ILL DIE ONE DAY I WONT BE HERE TO TEACH YOU
Ответитьis gable flashing necessary for water prevention or is it just for aesthetics? I would like to have no gable flashing
Ответитьخاصني لاطات
ОтветитьHello,
Could you be so kind and tell me the name of the animation software that was used for this excellent video?
Thanks in advance.
very durable roofing almost without maintenance, but seems too slippery and much difficult for gutter cleaning if going to roof
Ответитьthis is an awesome video. Thank you for doing this.
Ответить