Комментарии:
As some viewers have pointed out, running a much longer screw (3" screw, for example) will often remedy this. It drives deeper into the actual framing rather than just the door casing.
ОтветитьThank you 🙏🏼🙌
ОтветитьGolf tees work wonders in house hinges. Just glue and smack it in the hole.
ОтветитьWhat about steel screw holes?
ОтветитьChicken skewers here. Thank you. The toilet is forever grateful.
ОтветитьWhy not use a longer screw?
ОтветитьThank you.
ОтветитьI ended up using a left over wooden dowl from putting together furniture to fill the screw hole. It fit tight so hammered it in with no glue and drove in the screw. Worked well
ОтветитьI did this in wood cabinets and it worked great! The closer at top of storm door completely pulled out of door - all three screws. It is a metal frame. Would this work also for metal?
ОтветитьIt's worth a try.
ОтветитьI used matches in the past. Don't use a electric screwdriver or your stripped the freds😮
ОтветитьYou are helping me solve a problem with two 10.6 lb. cupboard doors (ridiculously heavy)! Thank you so much for the easy fix! I hate it when I have to fix a problem before I can fix a problem, so thank you for my secondary problem fix! 😄
ОтветитьWorked perfect for my Wash room door. Side note: couldn’t find my wood glue so I sub with Money glue. Thank you so much for sharing this.
ОтветитьYou should cut away the thin tips before you cut to length. That way you get full width of the toothpick all the way into the hole.
ОтветитьThank you for sharing this cheap, easy trick. It’s just what I needed to finally fix my doors.
ОтветитьThank you!!
ОтветитьThank you from England.
ОтветитьWill this fix work for a metal door frame, or only if the door frame is wood?
ОтветитьWhat if the hole is in a cement wall? Can I follow the same advice?
ОтветитьWhy not just inject wood putty into the whole then drill a small pilot to rescrew?
ОтветитьGreat video.🤜🤛Thanks.
ОтветитьWould this work for plaster walls too? I think it's worth a try.
Ответить"My kids hang on the door knob" yes that also why I am here brother
ОтветитьI use matches. Also you don’t really need the glue.
ОтветитьBrilliant! Thank you!
ОтветитьThis but use gorilla glue
ОтветитьI’d think you should screw in the screw before the glue dries. Seem to me doing it after the glue dries you might be breaking the glue bond.
ОтветитьMatch sticks if you cut the ends off work very well also. Thank you! For this video.
ОтветитьThank you!!!
ОтветитьBrilliant thanks
ОтветитьThanks so much for this video. Sorted our door out. Cheers.
ОтветитьIt's not going to keep the holes centered and only works so so. The door is going to eventually loosen these screws again.
ОтветитьThank You. It helped 😅
ОтветитьWhat is that watch that you’re wearing?
ОтветитьI usually cut a shim or toothpicks and pound it in with some wood glue and it’s always worked . See you know already , haha . Good man 👍👊
ОтветитьThanks
ОтветитьThank you Brother..mmyyGuyy👊👊
ОтветитьWhat about plastic?
ОтветитьWill this work on metal screen doors
ОтветитьWill this on MDF door jams.
ОтветитьThis works 👍🏽
ОтветитьThanks for this video. I’m a single mother and DIYer…I just looked at a couple of your vids and I love your channel. I’m Subbing right NOW! Thanks again!
ОтветитьThank you. My bad son did the same and boom it’s hanging lol
ОтветитьThank you buddy❤
ОтветитьAwesome video. Will this also work on a aluminum hole with toothoicks and wood gkue even thoughits glue made for wood? ....its for the bottom cover on a wcreen door. The little metal sheet that coveres the bottom from letting air our.
ОтветитьWhat happens if the toothpicks fall into the door frame like mine do ?
ОтветитьI used a kabob skewer with no glue and it worked great. Thanks!
ОтветитьWood chopsticks also work well
ОтветитьThank you so much…..
Ответить