How to Bond Metal Brackets to a Metal Tank Without Welding

Vertical welding is supposed to go uphill, bottom up. Your weld has no penetration and is still burning the other side. Squirt gun might be the wrong tool. TIG offers more control. Copper backing or solar flux can help mitigate burn thru as well. The only time I would think to glue something like this would be on a fire or explosion hazard.

Without a strength test what's the point of this presentation? might as well use double sided tape.

That shows it used on steel, but how about other materials like aluminium to aluminium? I look forward to the stress test video.

Does 1212 cure hard and can then be sanded? Thanks

So why was welding the tank unsafe.

so this is pretty much JP Weld?

Kahoot music

Okay now let me hang 4,000 pounds off of those two load points for scale calibration.

Is the Belzona 1212 bullet resistant ? How much impact force can it withstand before breakdown at the molecular level. I am interested in a cold bonding product that will resist the force of a BMG 50 at VERY CLOSE range. Thank you for the help

How will it stand for exterior installation, forever?

Brazing is better than welding when it comes to thin-walled thank like that, but even brazing tends to warp the thin metal, while cold bonding does not, so for areas that do not undergo extreme temperature swings, cold bonding is better. But for areas that get extremely hot, then extremely cold, brazing is superior to cold bonding in the long run.

Where are the load testing videos?!?!?

Would have been nice if you had shown some stress testing after it cured. and how it held up over time.

Great vid thanks l. Would love to see a load rating test.

Can I use this to glue my prosthetic arm to my stump.

Cold bonding does not mean what you think it means...

Useless without strengths….. interesting welding technique…completely wrong welding down like that…

Dude in the white Tyvek suit looks like a young RDJ (Robert Downey Jr.)

LOL, where's the load testing part?

Useless video with no real measurements and testing between the two techniques

...interesting product I just found...at the company - do you have comparison OF STRENGTH of those 2 ways of bonding ?
.. or any lab certificate for it ?
...WILL YOU EVER ANSWER THIS QUESTION ... so many people like to know and it seems you do not have the answer ...

At a cost of 300 € for that tiny amount, nope.

The kahhot sound

I could do that with plasticine.

Ok but how strong is it?

Looks like J-B Weld to me !!

Yes, you did no stress testing so I guess I'll have to go find your info myself.

pull test .. hello!!!

If the contact area is of 1 sq cm between two metal pieces (the same used in auto parts for example) what is the maximum holding in lbs or kg ?

Looks like jbl weld

Very interesting indeed. Still looks like $80 of “JB Weld” in a can. To bad you did not let it fully cure, then start hanging weights on, to the point of failure. We all know enough weight would eventually cause separation. It would be cool. Let’s say the contact area is 6” X 6” (15.24 cm X 15.24 cm) = 35 sq in (232.26 sq cm). If properly prepared, if the bonding agent holds 180 lbs. per sq. Inch, it could hold up to 1080 lbs.
As shown, priceless is working on the outside of a coated tank, like galvanized to glass lined like a tank style water heater. That is something!

How about some TENSILE STRENGTH tests??? How does cold bonding compare to welding, brazing and soldering?

How does it hold up to heat? For example, if it was applied to a metal fire pit.

Dear sir,can I fill this solution to mild steel welding blowholes

If that epoxy takes a whack with a hammer, will it just break off ? How about lifting capacity compared to the weld ?

It's good and all but I would not risk my life on this stuff. If you weld a ladder to a 200m pillar, I trust it.... "glue" the ladder on with this stuff... well.. I'm not climbing that thing.

Can smooth or polish surface be bonded by this? If not please recommend what should I use, to bond smooth surface..

Can bond stainless steel block on High speed steel.

for the above video, what is the cost of cold bonding to welding. What is the bonding strength of cold bonding to welding in the above video, if possible can I get the strength value of cold bond strength in MPa. Time taken for cold bonding making to that of welding time. can i get the data please ?

Will this bond steel to aluminum?

Is this epoxy connection acts as a conductor? or will it pass current?

Impressive

Works with stainless steel?

Why not conduct all welding then apply the tank lining. Welding done correctly is always more dependable than glueing.

The back ground music reminds me of the Kahoot music

1. Please tell the one doing the grinding that the gaurd on the grinder is wrongly positioned.
2. Just as welding is tested with NDT, What are the tests done to ensure the cold bonding is done effectively?

por algo somos los mejrores