INSTALLING THE V6 MOD KIT

Thanks for the awesome vid! Any specific reason you did not solder the ground pad on the modchip?

Nice Video , hey I have a switch with the chip , the guy did a excellent work, He installed a Retroarch that looks just like Crazy Mac build , do you know how to install that build or can you make a video about it , thanks

Hi, what is the value to measure with multimeter for these points? I’m stuck with green, purple, white light then boot to OFW. 😢

Do you use solder mask? Why or why not?

So can this type chip be used on the patched model regular switches?

I'm not getting any reading from the B point, ive resoldered it multiple times but no luck. All other points are giving the appropriate reading except B point? any thoughts?

question where did you get all the items you needed can you provide an full list? thanks :)

Hi I accident removed the capacitor next to the emmc chip when shouldering. Do you know where to get it back?

Wondering why my screen is black but
Chip
Is just pulsing green

What size of wire do I need for this? As I don’t think it comes with the mod kit. Thanks

Is this hats also ban proof already, beacause wheb i testes with 90dns it says not blocked.

Honestly the only part that scares me is getting the CLK (D point) soldered correctly. Exposing traces isn't my strong suit.

After sitting on the dock for a while and i reboot, it no longer works. If i open the back cover and close it again, it starts working again

Update: After 7 reboots without doing anything it boots into cfw. What could it be?

Did u know how much measure the clk point without battery conector insert? Here show 1582 but i think this value is very high!

Thanks for your video, it is well explained and the image is clear. I've done two OLEDs thanks to you, but on both I had no reading on B point (OL on diode mode) but after checking and doing the soldering again still no value, I gave it a shot and it worked just fine. For the second switch I had 480mV on the DAT0, i tried reseating it several times but best i could get was 495mV... I tried it and altrough the training was a longer than the first it works like a charm.

Good video, but my solder iron is to big.
What temp are you solder? My 0.5mm tip is on the way.

I have the following issue. I installed the chip using the flex cables in the kit. All the readings are present and all the points seem to be soldered properly. The chip works the first few attempts but after a bit it refuses to work. it flashes the purple light for quite some time, goes into the glitching process and then goes back to purple before showing a red blinking right that blinks 5 times. I decided to open up the switch, change the DAT0 cable and resolder the clock point where you need to cut part of the CPU shielding. It seemed to work for one day and now the issue is presenting itself again. I have no clue why it refuses to work

Is it not necessary to ground the chip?

Well looks like I need to revisit this video 10 years later whwn Im not scared of electronics

Best vidoe tutorial! Best music as well thank you

I bought modchip but don’t say instinct ? Do I need flash the modchip ? Or can use straight outta aliexpress it the v6

between this and picofly , which do you recommend for V2 . saw some issue with the picofly and now still deciding

Can I swap out the V6 chip with the picofly and keep the same ribbon cable and wires?

Ini adalah video tutorial terbaik yang pernah saya lihat, langkah demi langkah d jelasken dengan jelas, terimakasih , dan sukses selalu

For someone who hasnt done soldering how hard would this be?

Tutorial inject software for this instinct oled v6?

Anyone here know good links to buy the mod chips? I see so many different ones on ali but no clue if I’m going to get ripped off

Do you need to patch or update the nx v6 chip once a new switch firmware comes out?

good video, i have a question, how i know if the cable is the bes to make the jumpers ? i cant get the awg36. Thanks for the help.

Hey, where did you get the chip from? All i find is the HWfly lite v6 but no hwfly v6. It looks different from yours. It has no dat0 adaptor or anything. I'm pretty new to this could you help me.

Wew.. I failed at the D point soldering, I accidentally pulled out the diode beside when trying to remove excess solder with desoldering wicks, didn't notice it actually sticks to the diode not sure how and I didn't remove the wick with carefully enough. The diode came off and gg 😢.

If anyone can help!!!??

So, after installing the chip, I get no power on my screen. I get a blinking light of red, green, yellow/green, solid green then purple, and flashes white at the end with nothing happening

Thank you for video. Is it necessary update firmware v6 chip?

Just for the record, my B/RST pin measured as open loop, but everything still worked. I checked every pad and trace connected to it haha

Strange, I was getting the infinite purple and then red and boot to ofw. I opened up the back to look at the chip and without touching anything, I tried booting it up and it booted fine to cfw... I wonder what happened? Loose wiring? They all felt tight

Great work. Do you know the value of the capacitor in parallel of the 3.3v point Nintendo switch oled? I pulled the flat and ripped one of them off... the video game still works, but I want to put another one back. thank you very much.

A heads up to not put the mod chip too close to the Tegras cooler, if you do or have to too much pressure the modchip won't work and your switch won't boot.

Great touch with the troubleshooting section. Great for anyone who has paid for a dodgy install and later had to repair. Much appreciated

Hey, thanks for your nice videos!!! Good Job! Maybe do you have the schematics of the board I need to reflash firmware 😢….

Please help. Any idea why everytime I start putting back the metal shiedl, the chip keeps trying to glitch indefinitely ? Kapton tape on both side of the chip I don't understand what could be the cause ?

Can you please give me any tips for re-attaching a resistor to the CMK point? I've tried soldering it, but my soldering tips are too big, I've tried hot air and although it looks like it's attached, it just doesn't attach. Is there some kind of technique to soldering one on?

So you used 36awg for all connections?

Will this work with the non OLED model ?

Easy peasy, thanks to you :)

Very interesting video! I am in the D-B-A situation But I have a Hwfly chip. Do they have the same status LEDs?

What happens if you damage the CLK or CMD points? Cause I think I damage the track of the CLK and the resistor has been damaged for the CMD and now the OLED won’t turn on even without the chip.