Комментарии:
Por favor, é realmente possível usar uma pistola tipo de cola quente para derreter plástico?
ОтветитьPuf, demasiados pasos y demasiados materiales y herramientas solo para pegar eso. Yo pensé que iba a tapar el agujero, el trozo que falta, vamos... Para lo que hace no bastaría con un buen adhesivo?
ОтветитьLol😂😂😂😂
Ответитьwow expansion of sight
Ответитьnylon is not something you want to breathe in, kind of poisonous.
ОтветитьThat bumper skin is cheaper to buy than the zip ties and glue gun.
ОтветитьToo bad he didn't use an anticorrosive paint 😅
ОтветитьEsa reparación no sirve, debió meter una alma de fierro o grapas y después sellar con el plástico negro..saludos
ОтветитьGracias encontre este video y me sirvio de mucho se me partio una pieza muy pequenita y no tenia idea como repararla . Claro que me sirve
ОтветитьКласс! Бампер -АВС пластик, стяжки -полиэтилен. Эти материалы друг с другом не взаимодествуют
ОтветитьCuesta derretir las bridas jajajajaja
ОтветитьНикакой связки держать не будет
Ответитьmelhor derreter esse plastico uma panela e depois jogar na peça que você quer arrumar
ОтветитьI got to try this
ОтветитьПОЛДНЯ ПОТОМ ЧИСТИЛ НЕТ УЖ СПАСИБО
ОтветитьSo many wrong things condensed in one video.
The beautiful part is that we still can see the crack from the front 😂
The purple zip ties are plenum rated and won't produce toxic fumes like the non plenum rated black and white ones.
ОтветитьSanding and painting the backside. Useless steps.
ОтветитьWould loon less tidy but better to leave thick layer on surface to nake stronger.
ОтветитьI know this is old but why do all this when there are several plastic epoxies on the market that would do the same thing in 5 mins. 😂
ОтветитьСколько уже говорили, что это сомнительного качества работа. Стяжки это нейлон, а бампер ППР или другой пластик.
ОтветитьYour plastic welding skills are amazing. I'm always watching and learning from you. Thank you for always sharing useful tips for life with the community. Good luck.❤
ОтветитьMuy buen video, simple y explicado con los pasos precisos, felicitaciones.
Ответить...даже на этом видео понятно что мы обезьяны...
ОтветитьNot a bad idea 👍 it’s a good start for others to add in their knowledge and experience also to get the best results 💪
ОтветитьIt's way easier to just use a low grit sand paper or disk and sand the cracks out a few inches. Use fiber tape to cover them and then apply 2 part epoxy over it.
Ответить凄いですね! 感服しました 道具はどこで求めればいいのでしょうか?
ОтветитьInstead of removing and discarding it, I would have mixed the plastic raised by the Dremel into the initial melt.
ОтветитьBS
ОтветитьНи чего гениального,всю жизнь так лечим пластик,даже не снимая.Только это все на разик,до первого даже незначительногоприжима и все развалится.Только с накладкой пластины изнутри будет нормально держать.
ОтветитьSilikon tabancanıza silikon dışında birşey sokmayın tıkanır.
ОтветитьХерня это всё. Развалится от мало-мальского усилия.
Во-первых, непонятно, идентичны ли пластики на бампере и стяжках
Во-вторых, при наплавлении пластика в местах соединения пластик должен быть расплавлен и на самой детали, иначе расплавленный пластик приклеится отдельным пластом, а не смешается с деталью.
В-третьих, шов делают с обеих сторон
Impossible
Ответить🙋♂️amazing 🧡
ОтветитьGreat way to heat weld
ОтветитьNo! Wrong! Do not do this!
ОтветитьПластики делятся много видов, но этот пластик к друг другу не совместим держаться не будет. Полный чушь.
ОтветитьQuero ver é recuperar retrovisor de plástico no pé onde roda o retrovisor, isso eu quero ver
ОтветитьНе будет держать. Чтобы паять бампер, нужна та же смесь пластика из которой он сделан или очень схожая. твердая. А хамуты по сути из капрона\нейлона. Они не вплавятся нормально. Уже давно проверено.
ОтветитьДля этого есть рем ленты и фен😂
ОтветитьWas that Glue Gun used with regular Glue Sticks before ?
I tried the ties in my Glue Gun and the old Glue from a stick wouldn't get forced out anyway and the ties wouldn't feed.
Thank you for that professor I'm doing that tomorrow and save money from going to a body shop. That was great Thank you
Ответитьpiu-piu-piu!😄
ОтветитьWhy did he change glue guns? The title shows a cheap gun but the video uses a much larger gun. Weldbond ;)
ОтветитьGood Job...👍👍👍
Ответить👍👍
ОтветитьThank you so much! Interesting and helpful hacks..looking forward to more tips❤
Ответить