Комментарии:
Hey nice tricks no wonder ur bitch ass needs to hide like a scared ass motherfucker
ОтветитьGreat job, so simple, helped me.
ОтветитьThank you so much. Your video it's appreciated.
ОтветитьThis is exactly what I needed. Than you for starting from the beginning and going over everything.
ОтветитьAhora si que lo veo claro, gracias
ОтветитьGreat Video!
ОтветитьYour video was very helpful. I have power at the switch and tried to connect to a ceiling fan using 12-3 wire. When I flip one switch, I get power on both red and black wires (opposite side of hot wires). Any help?
ОтветитьGot it working. I have 3 lights and 1 outlet. Thanks!!!
ОтветитьThank you
ОтветитьI had a situation with MC where I wanted a clean installation with a straight run to the switches. In the middle a junction box and a leg with two lights. I had 3 conductor with a green for ground. At the junction I used the white wire to carry the load to the double switch and the black and red wire to carry it back to the lights. I wrapped the white wire with black tape to signify danger. Lights work great and I conserved wire. Did I violate any codes?
ОтветитьThank you. The best explanation. You solved my problem.
ОтветитьGreat job man…🎉 great vid and very well explained for my small mind…
ОтветитьYour video was exactly what I needed!
ОтветитьGreat explanation thanks!
ОтветитьSaved my life
ОтветитьThanks i really enjoyed.....
Ответитьexcellent video
ОтветитьThank you, Mr. Flores. You may speak with an accent but obviously you don’t think with one. Nicely done.
ОтветитьVery well done
ОтветитьExcellent video. Thank you.
ОтветитьCan you make a video where there are 2 power feeds into the box and you break the middle tab on the switch to make them independent?
ОтветитьYou rock Sal
ОтветитьThank you!! We struggled for an hour until we watched your video!! Black screw = hot!! 💡
ОтветитьExcellent video , great explanation on how you wired it up , Yhanhs.
Ответитьexcellent job.
ОтветитьThanks.. You made it So Easy... 👍
ОтветитьAnd this is exactly what I needed! Thanks for the clear video!
ОтветитьNicely done. You just saved me a lot of money with this short video
Ответить" ANIMAL " deverias de ver conectado el polo tierra primero por seguridad y precaucion 'BRUTO'
ОтветитьMy bathroom has this for the light and vent fan, but the fan will not come on unless the light is on. Why? Is it wired wrong?
ОтветитьHello Sal Flores 77:
Thank you for showing me how to do this.
thank you Sal. I appreciate your video. Very helpful.
ОтветитьThanks 🙏
ОтветитьSal but what I want is to connect light. And exhaust fan , ido have in the box red Black and white wire coming from the fan Where they goes to. Please apréciate your Help on it Armando. Mi name. So I’ll be waiting for answer.
ОтветитьI have a light switch just like that. 1 switch controls a light inside and the other was a spotlight outside. I just installed a ring spotlight cam. I need to remove 1 switch from accidentally being hit. I was thinking of just electrical tape or bar over it with a screw. Can I just tie the 2 wires together instead of on switch and wire cap it? Thanks for any help
ОтветитьThank You... you made it look easy and took a lot of fear out of it. I always turn off the power... it was just... how do you make sure you have the wires connected the right way!! thank you... you showed me in a very nice way... take care of yourself.
ОтветитьNicely done Sal. You are very good at articulating the necessary steps. Great display too.
ОтветитьThank you sir. Very simple and good instructions.
ОтветитьAbsolutely perfect detail! I was following this diagram for two outdoor ceiling fans w/o lights in my extra large shop.I have one for each bay, and even the leviton video didn't say to connect the neutrals together. I didn't feel confident, then I found your video. Thank you very much sir.
ОтветитьI HOPE YOU LEARNED HOW TO USE YOUR TOOLS BY NOW AND WHAT THE PROPER WORDS TO DESCRIBE THE WIRES BEING USED, LIKE A SWITCH-LEG AND LINESIDE, YOUR WIRE STRIPPERS HAVE 2 HOLES ON THEM FOR A REASON THAT EVERY ELECTRICIAN KNOWS WHAT THEY ARE FOR, TO BEND THE WIRES PERFECTLY THAT GO ON YOUR DEVICES, USING A NEEDLENOSE IS A HANDYMAN MOVE. YOU DON'T NEED TO WRAP ELECTRICAL TAPE AROUND THE DEVICE IF YOU'RE USING A PLASTIC BOX, IF YOU'RE USING A METAL BOX, YES ITS A GOOD IDEA.
ОтветитьThank you.
ОтветитьGreat video, thanks so much!
ОтветитьGreat job. Thanks for posting!
ОтветитьThanks for the upload, very informative 👍🏼
ОтветитьSal, you saved the day. Never knew to remove the tab for this kind of switch. Thanks!
ОтветитьGreat video! My bathroom light and exhaust fan are both on one switch. I only use the fan when I’m showering but don’t want it on all the time while in the bathroom. Can I use this type of double switch to separate them?
ОтветитьBest video on this subject. Thank you.
ОтветитьSo tried to wire bathroom same way it was before but different locations, welded a few wires, burned some wire nuts and tried to start a small fire. Your how to video just made my evening. Thanks
ОтветитьExactly what I needed! Thank you so much!!!
ОтветитьExcellent
Ответить