Комментарии:
I am connecting an atm machine (rj45 connection) back to a new circuit (rj45 cable). There is single mode fiber available from MDF to where the ATM is, about 200 meters. So can i attach 1 media converter from new circuit to existing fiber and at the end of the nearby ATM closet connect another convertor to fiber box and rj45 going to ATM.
Ответитьhi,
do you think the following schema is possible?
[ISP cable router] <--(rj45 // 250Mb/s)--> [media converter] <--(fibre)--> [Mellanox ConnectX-3 CX354A // 10GbE]
thanks :)
Sir, is it comptible the non giga switch (10//100base tx) will connect to 10/100/1000 base fx fiber switch?
ОтветитьSo let’s say even if the converter is capable of POE, do I still need power in? Power meaning the 12V that was shown in the video to power up the converters
ОтветитьMade as much sense two little boys kissing to me didn’t show where the node, antennas and source of signal plugs into the fiber radio or the fiber connecting to the terminal node controllers, etc. not even how to do an internet brief with your neighboring nodes in your network.
Ответитьshare email id i or contact number have doubt about multi connection using Media converter
Ответитьhere goes nothing................................ i was about to purchase 1 OLT and 20-ONTs........ on a 1 mile strech of road , can i use two 1-u chassis and 20- media converter? this will be cheaper and if so ....... how would i seperate each address to each converter? in case someone is doing something bad ? i do not want the cops kicking in my door , looking for someone on my network!!!! do i use static ip? or do i go the route of a olt/ont
ОтветитьCan i use a SC UPC splitter to split the fiber connection to my main modem router and to my wifi router that have a 15 meters lan cable.
Lastly does the A and B can only be use together or either of them can be only use as just one media converter?
Hello can i use one of these to convert my 1G ethernet to 10G FIBER and connect it directly to my pc with a sfp+ nic - i know still it'll perform at 1g speed but i'm futureproofing my link with the switch
ОтветитьI'd like to use a fiber link to help minimize the chances of an electrical surge caused by lightning to propagate beyond the fiber. I was hoping to find a pair of small inexpensive devices, where I could simply plug CAT-5 ethernet into each one, and connect the two with devices with a fiber cable. Are there any "media converters" made to directly accept the fiber cable without having to buy these separate additional SPF modules?
ОтветитьHello, can I use this to convert my DSL router then connect to the Fiber Optic Media converter which is going to hook up into a fiber Router for me to use?
Ответитьse puede usar este aparato en vez de un modem?
ОтветитьI have one question two fiber is must if connect single fiber obtic cable will work
ОтветитьWhich converter can I use to convert from isp directly to router?
Ответитьhow do I buy your products in India?
Ответитьcan i use fiber to lan just because my adsl router has more option than the isp router?
ОтветитьCan I use this on my ISP's fiber line at home so I could use my own router and not the ISP's default router?
Ответитьcan i use media converter to transfer files between computers,
and can you please give me the media converter RJ45 female connector pin out with pin description
price koto
ОтветитьGoodday! I hope you can help me. You see I bought a media converter for fiber to ethernet. I am planning to use it as a direct conversion between mu fiber line (the fiber ineternet direct line from the box) to my router using the media converter. Is that advisable? Also does the A and B media converter have differences because I think I bought B media converter. I already tried doing it (connecting from fiber line to media converter directly to my router since the router I bought doesn't have a fiber port) but the 2 lights for fx is not blinking. I don't know if my media converter is broken or anything but all of the 4 lights are blinking (all 3 tx lights and 1 fx the most below one is blinking) and the 2 lights in fx is not blinking. I hope you can help me. Thank so much!
Ответитьmy modem has no wan connection, it's just pon or fiber, can I connect it to media converter then using wan connection through router?
Ответитьhi, I have a question, is it possible to use a SFP module that can go up to 22 KM with a 100M fiber single mode cable? Will this damage the converters?
ОтветитьDoes this require you to have fiber optic dsl or any type of telephone internet connection to the home? From an ISP
ОтветитьHi, my fibre optic cable does not fit in my router. If I buy one of these, plug the fibre optic cable in, then use an ethernet to my router, shoulf it work? Thank you
ОтветитьWhy was your ping time 19ms with fiber? That makes me concerned about the converter. 2 gigabit switches w/even cat 5e should be < 1ms, no?
Ответитьi conect onu with media conveter
with out olt its posibal
I have a fiber optic port on my room if I use one of these converters does it work ?
ОтветитьDo you need to have duplex fiber?
ОтветитьI have a grasp on using the matching media converter boxes and the simplex optic cable. I am getting hung up on the proper module to purchase to extend a Netgear router to another part of the house to my office and straight to my computer over Ethernet. Could you recommend the correct part number(s) to achieve my home extension please! Thank you in advance.
Ответитьcan this be used to get a stable Ethernet connection to a computer?
Ответитьkindly recommend me a gepon/gpon onu single mode sfp module (Less than 20km).
ОтветитьWhat transceiver modules would you recommend for this scenario?
ОтветитьWhy dont you use narrations?
ОтветитьIf you already have SFP at one end, can you use a single media converter?
ОтветитьHi I want to inquire
Will a 1/24 PLC Splitter work with a media converter?
Gigabit Media Converter > 1/24 Splitter > Media Converter + AP (x24)
Excillent
Ответить