This Will KILL Your CPU & AIO Cooler! How To Install Cooler

Do not kill your AIO cooler or CPU! Install and Orientation is important! How are you guys doing?

But which way are your fans blowing? Pulling air in or exhaust?

So I use RED & Black in my setup ... Love ur Cable Extensions ... Where can i get these exact ones???

This video is so bad…

You should delete this video

This is so rong lol the way he had it first was actually the best way to have it lines up not down ur forcing the pump

Not true, I have the radiator installed on the back (Lian Li 011 Dynamic) with lines up (couldn't turn it upside down because of how the case is built), and the air stays on the top of the radiator because the pump is lower.

I can agree with that the pump should never be on the top over the radiator, because of the air causing working the pump in dry environment.

wauuuuuuw this guy is totally wrong !!!! dnt even point your radiator top down becasue the will go into your pump not the opposite way woooooooow this guy is talking a lot of bullshit. I had mega big issue when mounting my radiator on the bottom. This explains how stupid people are believing every bullshit what influencers saying. There is no different by mounting on the top or fron in thet op. This guy is tellling others bullshit

I call BS I front mounted 2 PCs I built with tubes up and guess what? 5 years later both still work PERFECT

THANK YOU!!!

Lol, wrong.

ARGH building (another) rig for a friend and i didnt pick the parts and they got a HUGE AIO rad in a mid tower ATX case and im looking at this same issue have to install it with tubes up :(

why are u so close to the camera

-rep Überschrift/Titel aud Deutsch und dann lebbert er nur English! WTF? This is a no go!!!

🤣🤣🤣🤣🤣🤣🤣

This is misinfo and the video should be taken down. All that matters is top of the rad is higher than the pump. You will NOT kill the pump having tubes on top vs bottom. This video creator is a moron. 7.7k likes...that is terrifying.

Turned mine upsidedown and ran it, this fixed the air bubbles

İt doesnt matter dude

9 minutes of white noise. Stop it!

1. I would never take advice from someone wearing a hat like that.
2. Listen to what i say and not what i do.
3. Air? What a hell you on about? The product is air tight.
4. Regardless where you put the water cables theres always going to be pumping up or down.
5. Sure, the best way is to put the water cables receiving the hot air from GPU 🤦

this is bullshit! at top of the vcase is good,
at front with tubes over the pump is good,
at front with tubes under the pump is good,
but lay down at botton is worstcase
why i know it its ez i love itx pc´s and ive evertime aio´s in the tiny pcs bcz. aircooler sucks mosttimes at tiny cases (not at cooling but at loudness!)

when you say in the video you're not going to make this long drawn out and boring you are doing exactly that. adding conversation that doesn't co tribute to the subject matter only drags out the video making it what you're saying you're not going to make it.

I saw a video about Msi Mag Coreliquid C240 and someone on the comment section said this:

"Be very careful as MSI is showing it top mount in pics. This AIO is unique it's pump is in the radiator not the block that attach to cpu. If you top mount there will be air bubbles up there as it's higher and will effect tube suction and likely lead to early death. I read people online who had theirs die within 2 to 6 months while front mount no issues. I had mine top mount for 2 weeks until I realised thankfully seems no bad damage it's now front mount with tubes coming out of lowest point (tubes bottom ideal but top if they can't reach still better than to mount it top). I also get much better cpu temp while my gpu went up just slightly no big deal. Best of luck."

Is that true?

okay sound wird, my mashine run it WORNG! so if i go to change the radiator to what u say, will i have better pc then xD ?

You should not blow hot air from the radiator towards the inside of the box. If those fans at the front were reversed you would be fine, as long as the rear fan was also reversed to bring cool air into the box. That is one reason why using the radiator at the top is better, because people don't make these mistakes.

Ok your camera way to close and face a bit blurry other then that thnx for the Info.

i just inherited my first water cooled system its mounted in the top tubes down but what is odd to me is it is sandwiched between two fans both blowing towards the coolers radiator this seems counter intuitive to me is this ok or do i need to reverese the fan pulling air into the the radiator from outside so that it will actually exhaust?

this video bad -wrong , for stuped people

if you are running a 360 rad chances are you do not have any other options than having the Rad mounted at the front!

You need to adjust the camera frame

mine doin just fine

1000th comment 😁

Nothing wrong running it like that at all I have done hundreds of hours of testing on this 😂. It creates a natural syphon in a closed loop as long as the radiator is filled properly from factory. Ppl don't take this on board it's not true....

Is it right for the fans to suck air out instead of blowing through the heatsink to reduce heat?

Yeah. Don't listen to this guy.

I have problems fitting the radiator at the top as it get blocked by the RAM.
My AIO just died weeks ago I am done with AIO I'd rather get the aircoolers as they are more reliable.

Mine is set to be at the top, I have never seen piping at the bottom.

totally disagree, I have nzxt kraken x62 for 7 years now, rad on front and tube on top, pc turns on 12-24hrs a day. havent encounter single prob since day one I install it. Tested and proven no problem with that orientation.

Need a guide to extend the pipes..

It doesn't matter as long as you haven't trapped the air in the pump in the first place. Just run it with the rad above the pump for a short time. The lines at the bottom are the best however, not because of air gaps but because of the thermosyphon effect.The pump will pump hot water to the bottom of the rad which, being hot will rise up naturally, assisting the pump. As it cools after the rise up it will sink down the second half of the rad because its denser. this effect reduces stress on the pump and in theory could mean some flow even if the pump isn't running

1000th comment 🎉🎉🎉

Should have just given us the link to the gamers nexus video

So long as the pump is BELOW the loop, you're good. Doesn't matter if it's 5cm, or 50cm, or having up and down pipes, that's irrelevant.
Stop saying it's bad, it's not bad at all. Spreading misinformation is bad

As I expected, no fucking idea. The only thing is so bad is the information you are giving

So what about top mount but with the lines to the left rather the right?

Just bought a Thermaltake view 71 case wit Thermaltake aio. I didn't realised he had rad outlets st top? The pump was under these outlets. However air sits at top of rad so it definitely had air through it. I'm hoping the pump doesn't need water to lubrication the bearings? Thanks for sharing

Hey my aio is at the back of the case