10 Steps Painting A Room FAST and EASY

Why does it say "phillipians 4:6"😮whatever i like😊🎉🎉

You did a good job with the description!

I don't use tape unless it's dental work.

That wasn't a 9" roller he used 😂

Great video..however, isn't sanding a crucial step as well?

This comment has nothing to do about painting, but I just had to tell you your really good looking! 🤩

Finally. A profesional painter who made a video geared towards a homeowner or an newbie. All these other guys are posting clips where they are using 18 inch rollers over floors covered with rosin paper or chip board.
In been a painter for 36 years. The steps you described along with the tools you recommend are perfect. Well-done

Still trying to get the hang of one coat cut ins. :)

I don’t mind painting and I’m fairly fast. So long as someone else does all the prep and clean up. So I can just walk away. Lol.

Thanks for keeping it real Chris! Great paint tips.

Apprentice painter here these tips really helped out a lot. Thank you !

Y say u only using a 9 in roller then use a 18? I almost always use 18's on everything

Aloha looks great ! I am following these steps today 🎉 Taking a quick break then on to my first coat & cutting* have a nice day !🌺

I like this .

Don’t need to sand inbetween coats ?

This was a really good video. This was about as quick as you can make a thorough video on something. I'll be rewatching this a few times before I repaint my house. Thanks.

forward to 5 or 6 mins because the beginning is too much talking.

Thank you so much!! I was like I could never do this but I think maybe I can ❤

what is everyone's go to place to buy paint?

Thanks for sharing. This video is very helpful and informative.

I'm actually surprised that you only cut in once with a thick layer, but I might try it for my kitchen. I don't paint professionally but I do enjoy it. Typically I cut in, roll, cut in again and roll again. This requires my Frog Tape to be removed after paint has dried on it. So far I haven't had any crazy issues.

Room looked great white. Too bad they painted it yellow, it looks dark and ugly now.

How quick was your second coat actually on ??
My Sherwin Williams Emerald says 4 hours in between coats 😢

So how long did this whole process take you including washing your painting material, etc ?

So iv painted a room blue and managed to get it all over the skirting boards i forgot to use tape, cant get any of it off without scratching it and making more damage

Wife and I were bubbling around trying to get painting our house and found your channel. Been binge watching and learning and and also subbed. Great content thanks so much.

Looks easy but it’s not 😭

Awesome job guys, what colour is the ceiling???

the bible sucks

Looks like you went home and showered

What about that spray machine? Does it really work?

Thank you 🙏

I missed the part about using the caulking gun. What or how did you use that for?

🤘🤘🤘🤘

New viewer your videos will definitely help me with my job training

Remove tape before paint dry, so I mask the baseboard again before coat two?
Thank you 😁

I usually sand, throw a light coat. Spackle anything that stands out after first coat. sand, paint patches and cut twice and finish with the roller.

THANKS FOR THE GREAT VIDEOS!!! cut in AFTER rolling?! Everywhere else I've seen say do cut in first. The roller goes into / over the brush marks for a more consistent look? You do say to cut in 1x when possible, So the 2nd roller coat will wind up covering the brush marks I guess.

Is the ceiling the same color? Or did you use tape to hold the line? Also what type of paint did you use flat or satin in the walls? My whole house is one color. And I think it is flat paint. I bought satin and now worried I should have gotten flat. My kitchen , living, hall, dining are basically one large room area.. so I wasn't sure what to choose. Advice please!

This was great thank you!!

So do you have/need to use a primer?

2/16/2023. Yup you vacuum, yup I’m still watching ! 7:30 am Indiana. Still got good material brotha!

Great video. Thanks for really quick run down on how to paint and the tools and preparation needed. 18 inch roller is the key to do it fast

Wtf is a cut in why using these terms without explaining them?

Definitely John Cenas doppelgänger

I have a question why are you cutting in afterwards? Having a professional painter as my husband. When you cut in after in the paint is tacky you cause clumping so I'm just curious why you're doing it after and not first?

How in the world was this man invisible? Mind blown

So no cleaning the walls??

Watched it at 2x speed😂

I use 12s or 14s, . 9s for bathrooms , then I spray out ceilings and closets with same flat white. I also use the same setup as you do. 1cor 15: 1-4