Комментарии:
Me laughing knowing my bmw is gonna hate me because this is money intensive and time consuming 🤣
Ответитьmy car clicks when i reverse or when i put it in drive its coming from the rear right wheel idk what it is
ОтветитьQuick Question: will tightening the axle nut fix play between the drifeshaft and hub splines causing a clunk on load changes? AKA 'axle-ping'.
Thanks
mine look fine like new but i hear click clic lcik especially if i run backfwrd turing right, camry 2008 now they sell regreasing kit but i wonder if its gonna fix the clicking noise!
ОтветитьHi guy i noticed that one of my rear axle inner boot rubber closer to the diff was torn and most of the grease had come out, while i was putting back grease in it i saw pieces of the pin metals falling out. Does this mean my axle needs to be replaced? Thank you in advance.
ОтветитьWhat is the clicking noise actually caused by.
ОтветитьDoesn’t matter about the clamp, because the shaft has gears
Ответитьdude Vehicle has no "r" in it.
ОтветитьPorsche Cayman next to me put his spoiler up , I thought " thats f*****g it" ... nailed it ,he was dust , boost pipe comes off, my car is the only one in the world that wont run with intercooler pipe off , hard shoulder (side of the freeway) lots of Debris , punctures BOTH inner and outer boots, alternator gets coated in grease aswell as debris , engine strap snaps some how.....lots of fun in a classic Ford ......Porsche Cayman cruises past with a smirk lol
ОтветитьI'm at 100k miles with a noisy front bearing. I;m going to go ahead and do both right and left bearings and while I have it apart, go ahead and do the axles and brakes.
ОтветитьCan the outer Bering change how to remove it
ОтветитьWe used tie strap on the shaft
ОтветитьI got a b13 and the axle when removing the outer shaft just drop out is the c clip Bad
ОтветитьLiked and subbed thanks!
Ответитьthanks it was helpful
ОтветитьHey Len. Does a bad cv axle make the vehicle wobble when the vehicle reaches 35 mph and then goes away around 50 mph. No noise. Please advise.
ОтветитьExcellent demonstration. Thank you
Ответитьgreat vid man. thx!
ОтветитьI just paid 2k to get my axels fixed
ОтветитьZip ties can be used to fasten those boots.
ОтветитьThank you so much for explaining how the bearings on the inner joint have to be spread outwards to go back in if your axle falls out. I've been trying to get my axle back in, and it will not go back in, and I'm pretty sure this is why.
Ответить👸
ОтветитьMy truck making this clicking noise only when in 4x4 and turning turns while accelerating, why does it only during 4x4? Can anyone explain? Greatly appreciate!
ОтветитьGreat information and examples.
ОтветитьGreat explanation of "Axle Separation".... explained my problem. of why it's so long at the tranny side and won't shrink...... so I cant get the axle out!.... tried sawing the axle with a jigsaw... Ha Ha... it's made with uncuttable super hard steel... now I just hope to get the bearings back into their housing to take the axle out.... or I'll try the hacksaw :D
ОтветитьGreat video
ОтветитьAfter watching this video, I think I've figured out the clicking noise when I'm turning at low speeds. Thanks.
ОтветитьIf your boot is torn, you already have contaminants in the bearings.
Just replace the whole axel on the bad side. It's easier to replace and isn't really all that expensive.
Also: Find the ones with a lifetime guarantee.👍
I ha e 2017 ford fusion hibrid. There is some click weird noise when I go at 60mph. Transmission shifting is normal and everything else but noise is like on the front let bottom side. Tech put up the car in the rack and axles looks look besides some noise when he shook it back and fort
ОтветитьWoah thanks for the help with explaining more in depth and showing an example!!! Thanks A1 Auto!!!
ОтветитьVery very helpful! Thank you!
ОтветитьBe sure to appreciate how much easier it is to turn after new axles are installed. First time I did some full turns after replacing them on a GMC Yukon I was truly amazed.
ОтветитьWhat part of the video shows what causes the axle to click? Mine clicks as I let off the break
ОтветитьI usually just machine my own cv axles out of recycled pop cans wrapped with gorilla tape around my custom cv joint.....
ОтветитьDo you ever pack these with semi oil grease?
ОтветитьThat's not a race. It's a cage. The things you pointed to a few seconds ago are races.
ОтветитьMy equinox makes a clunk sound when slowing down, like something is sliding within its mount. Happens going forward but loudest when our in reverse. Motor mount?
ОтветитьWhat is GM car CV joint lifespan (years to replace)?
ОтветитьWill the wheel bearings fall out if bad?
ОтветитьA-1 Auto I had an issue with two Big Box Automotive stores, relative to my 2003 Cadillac Deville with 4.6V*. Each store stated that there was a left and right-hand CV axle for these vehicles but the left one was not available and discontinued; all except one! One store employee said that the left and rights were the same, which appeared to be the case because they were the same length when the axle was extended slightly, and they were identical in appearance. Question: Is this true, are they both the same axle?
After installing the axle provided the grinding sound from that side (left) of the vehicle has disappeared, I'm just curious at this point in time!
This guy looks chill I like him
ОтветитьI liked the dramatisation with the blowtorch !!!
ОтветитьWhat if my boot isn’t torn and it’s making a bad grinding/popping/banging noise when turning and reduced power jerking motion taking off from a stop….
ОтветитьWhat's A "Virhicle"?
ОтветитьYou guys are so informative, thanks
ОтветитьI just turn the stereo up when my 06 saturn makes clicking noise while turning
Ответитьhello there
Nice video do you deal with vintage cars ?
got a subaru vivio 4wd 1993 and desperate need two drive shaft left and right .
let me know thank you very much !!!!
Excellent video!
Ответить