Комментарии:
My rv valve stems are 1/2” rubber then 3/4” brass threaded for the cap, can I use flow thru sensors?
ОтветитьGreat job very well explained. Thank you
ОтветитьI have a new TST 507 and my display is nowhere near the brightness of this one. Fully charged by the way. My other problem is my RV has the inside the tire sensors which makes this very frustrating. I’m sending mine back to TST so they can check it out, just waiting for them to approve the warranty! Very nice folks at TST an Techno RV.
ОтветитьHi Eric
Good Video, I just purchased the 770 Monitor, do you have a video shoing installation for the 770? I purchased Flow Thru for the RV and Regular for the Honda CRV Tow Car. Thanks Dick Bathurst
Is there a way to reset the monitor and re do everything? My Nabor tried but no luck my trailer has the internal sensor any help would be great.
ОтветитьThis was the most helpful Video this week. I added a sensor for the spare tire and the programming video's you produced made it much easier. The manual is well written, but having the video's gave me much more confidence that I got the settings correct.
See you on the road some day.
Thanks for the easy to follow video I'm all set up now.
ОтветитьWe have had this system for over a year .....and still cannot get it to work properly....it just will not pick up the sensors .....It will flash the FFF FFF and correct position It will flash ID- LF....and goes right back to flashing FFF-FFF...This has been the most frustrating purchase I've had to deal with with this RV
Ответитьwhy didn't you show the real world, where on an rv you have dual axles? It's not intuitive how you pick the tires on a travel trailer, this is set up for a truck trailer.
ОтветитьMy only complaint about the physical product is the cheap suction cup and difficult to adjust knobs, specifically the one near the display.
This system is not cheap. So why use inferior components?
Very complicated instruction booklet. Whoever assembled it should be gone. This video explained the install perfectly.
ОтветитьEric, Be aware that TST has changed the BT chips inside these sensors and the method to code them to the display has changed a bit. I had trouble coding my new 12 sensor system and after talking to TST support (amazing support by the way, when I called I got voicemail but did not leave a message because it was close to 8pm, they called me back anyway!) they informed me that touching the sensor to the display will not work with these newer caps. They told me to try 1", 2", 3", 4", 5" up to 6" away until I found the sweet spot and that worked like a charm. Might want to add this to your learning series. Best regards! Brian C.
ОтветитьOk so my new TST TPMS, has already paid for itself. Left Dayton this morning headed towards Michigan. Tires started out with a cold pressure of about 95#. Watched them all climb up to about 108# as I drove. About an hour into the trip, I started noticing that drivers side rear, inside dual had dropped to 99#,a few minutes later it was down to 98, and so on. I new something was wrong and backtracked to a TA that had a 4 hour waiting list, they told me about another tire place less than a half mile away that got me in right away. Took a couple hours to get everything sorted out, but ended up finding a leaky value stem. $45 later we were on our way with no leaks. Had I not noticed the leak, I would have probably made it much farther up the road, and possibly blown a tire due to the heat generated by the low pressure. Potentially saved me a roadside repair, tire, and maybe even damage to the motor home.
ОтветитьThank you so much for this video, with your help I'm all setup as the instructions weren't as clear as I had hoped they would be. Eric saved the day!
ОтветитьReally great instructions...the best. Thanks!!
ОтветитьIm trying to set the monitor and I can't get the system to move to the next tire. Yes I'm pressing the +
Ответитьexcellent .. Thanks for your help
ОтветитьExcellent video. Thank you.
ОтветитьThank you for this comprehensive, yet easy-to-follow video. Much appreciated.
ОтветитьClear and direct. Perfect instruction video!
ОтветитьI have a single axle RV. Based on the iconography of the tire wheels, do I need to scroll to the middle of the icons or can I just choose the first two left and right wheels?
ОтветитьExample I have 3 trucks 1 trailer so if trailer has sensors can I install one monitor in each truck and program sensors into all 3 monitors so that no matter what truck I use the trailer sensors can be monitored is that possible or are the sensors only able to connect to one monitor?
ОтветитьNeed video for the internal sensors on how to reset them thank you
ОтветитьH
ОтветитьThanks for the re-programming help! 😀
ОтветитьNeed to change one of my tire sensors position.. how do I do that?
ОтветитьThank you so much ! ----- with your help I got mine working just fine .
Ответить