Комментарии:
excellent video sir! but i just want to know, don't we need to put a resistor in Ib to drop it from 6.8 to 0.7v? i am sorry if i am wrong
ОтветитьExcellent Explanation, Good Animation , Simplicity
Ответитьcan you please controlle 100 volt to 30volt
ОтветитьHow can you change ac voltage from a motor to DC to charge a phone
ОтветитьGreat !
ОтветитьWell, seems the engineer's not so foolish after all...
Ответитьthanks ! I got important role of Z-diode .
ОтветитьCan i use n channel mosfet instead of bjt
ОтветитьA few mistakes in this design. 7.5v supply and 6.8v zener is not allowing enough difference for the time when the battery voltage will fall during discharge. 1u capacitors are far too low to make any difference. You need 1,000u for each amp of current you are delivering and this will only improve the regulation by a few volts. But we don't even have a few volts "up our sleeve" in this circuit so both electrolytics should be 1,0000u.
The instructor really does not have a clue how to design the project and I would not employ him for one day. That's why you have to know about designing to get a job in the electronics world. Otherwise you will make a fool of yourself.
Thanks for video.
ОтветитьThe problem is the voltage drop in load at some amount of current
Ответитьthe background music is quite distracting esp when listening through headphones
ОтветитьFirst u study English
ОтветитьCan you also explain the same, if we replace zener with TL431 for precise tegulation?
ОтветитьSimulation and explanation thanks
ОтветитьI will recommend you to use lower capacity output capacitor like 200uf or something and use a load resistor in output with a value like 1 kOhm or 500 Ohms, or reducing voltage will be a trouble, don't be like you have to follow 100% Video, if you have knowledge, apply it or you'll never learn
ОтветитьDamn, that is some good explaining
ОтветитьJust another stinking IC, nothing to do with the varable transistor zener.
Ответить🔥
Ответитьhow do you calculate for the size of the capacitors?
Ответить"Small ball of guts" what does it mean.
Ответить😍🙏 नमस्कार
Ответить12v voltage regulator with good efficiency which will not give up and i would be able to apply heatsink on it with good 2 Amp at 12v output with input varing from 12v to 15v?
ОтветитьWhy is the power dissipation of the transistor = (7.5-6) x 0.5? Can you explain where did the 0.5A comes from and why is the voltage across the transistor consider as Vout -Vin? In addition, why did you use 20mA instead of 10mA in the calculation for the zener and resistor power dissipation?
ОтветитьWhen you change the load resistor, for example to a lower value, the current increases, this means, the base-emitter current increases, which causes the Ir current to increase as well, which in its turn increases voltage drop over the resistor, which can be shift the zener diode into non stabilizing range. So, you should count for this min/max values as well. Can you describe how should you fully calculate this circuit?
Ответитьexcellent explanation about series regulation. thank you.
ОтветитьHow does this man this compare to the Linear Regulator in terms of noise and PSRR?
ОтветитьHi sir 48v dc regulator for dc alternator
ОтветитьGreat job!
Ответить👍🏻👍🏻👍🏻
ОтветитьSuper
ОтветитьAngrej ki aulad😄😂🤩
ОтветитьThank You My Indian Brother! 👋
Ответить