How to bend a RGB strip around a corner ⤴️

Hopefully this helps someone out there!

Ohh very nice, saw this after I installed mine. took too much time soldering that rgbw. I died watching this.

Thanks bro

It’s not dangerous to fold the RBG when the light are on?
It’s not ruining the RBG?

This isn't common sense? Like you got to make a video? How stupid are the people watching this Channel? Thumbs down, do not recommend this channel

Pls dont fold these!

Directions unclear, 🍆 now flashing RGB stripe patterns.

You are not folding RGB.... You are folding an LED strip.... Imagin you said "this is how you fold blue". See how silly it sounds... Lastly, you should not fold it..... You get a 90 degree connector...

Rgb is red green blue, "this is how you fold red green blue"

Folding my RGB destroyed it directly! Not good Idea! Sorry.

It works on sum types others will rip so be careful 😊

Nice brother thanks

Wouldn’t recommend especially if the led light strips have a ip65 or 68 coat as it would break the circuit and cut of the electricity from ever reaching the end of the strip and it could change the colours too.

This man saved us a lot of pennies

Or... cut the strips between the gold contacts and use 90 degree connectors. Much neater.

Noooo, over time the material stresses and splits leading to cracking and creates a clean split cut of where you folded. This will lead to failure.

I had led strips on my panoramic roof. I wandt vene folding the strip but after 10 months of having a slight bend, it just split.

Always provide ribon loop, to aliviate any pressur epoints that can lead to failure.

If you bought these at marshalls or tj max do what u want but if is 100$ kit dont doo thiss

Is too hard

How about you stop calling the programming for the light colours, what the product is. It’s a light strip. You aren’t installing “rgb”. 🤦‍♂️

Would have been nice 4 days ago 😂

Thank you so much man! I just installed my first led lights, I had them for a while but never got the chance to install them. This video helped me so much! I was wondering how to fold them properly. Thank you so much. 👊

Just buy the corner connectors

57th comment

Oh! Trank you!

"properly"

My directions literally has a picture saying not to do this lmaoooo

How do you cut it ? Please I’m to scared to cut it without knowing what I’m doing!

Not all heroes wear capes

No, you never fold rgb! In your case a flex neon rope/ silicone flex diffuser would have give a much cleaner and proper look.

My leds it’s says but I’m the microwave to warm the back up

Thanks.

Important to note he's in the middle between the LEDs. The closer to the bulb the higher the risk of causing separation of the bulb from the circuit. Not fun.

Of course I see this after I install mine 💀💀💀

ผ่านเติ้ล ❤ ค่านอน

What’s your table?

It helps... but the double side tape on my rgb strips r suck💀

I JUST SEEN THIS AFTER I PUT UP MY LIGHTS OH MY GODD😢 least i know for next time…

I tried this and my led snapt in half so don't try this

oh no.. i already cut mine im gonna cry

it literally says this in the notes lol

You’re a god damn hero sir and Australia is in your debt

Let me tell something if you bend like that you can destroy the connection in the led strip and your RGB will be paralyzed

Just cut it and solder it

improper installation

Can we be friends

Oh man! I wish I’d seen this video before I installed mine. Yours is nice and tidy. Thanks for sharing.🌸💕

OMG TYSM SO MUCH UR A LITTERAL LIFE SAVERR

this helped thanx

Thanks I just got some and idk what i'm doing 😂

Done it. Broke a line. Now it only R😂 G and B is dead.

what are the best RGB lights?