How To Build A Shed - Part 8 - Exterior Trim Install

whats the trim your using

C. Ñ mm.m...n..nki mg

Approximately how much was the total cost of this shed?

Nice video, but don't overdrive the nails on the smart trim. You will void the warranty if you do.  

Great videos.  Thanks very much.   

Thanks for the video series, they have been very helpful. Are those Utah mountains?

I can't find the right dimensions for the smart side trim near me. All I can find is 1x6x8. Is it ok if I use other wood for the trim? The smart side is cheaper but unfortunately they only have that length. Or could I buy the smartside and then cut it to the right width and then add 2 inches to with some scrap? Any thoughts =)?

Too busy to miter corners?

Do you have anything showing vinyl siding installation?

dear   beloved hello from tokyo japan.i d like ask you i have  interest to built a shed  design in  <  L  >  sizes  :i:   10X 2.60_ : 6x 2.60should be 3 meters highcan you help   with the   shed   floori saw you  had  fixed    woods in the  ground what should be   good  woods or    Slabs or  concrete   blocks ?thanks in advance for  the   information and guidances  and    so Thanks for sharing the videos .my e mail is   [email protected] bless you.A.costa

How long did this take you to complete? Man hours? A weekend?

Noticed that you are wearing a shirt with the Hawaiian islands cool. Really cool and well explained videos, thumbs up.

freaking nuts

Hello! What is the material that you are embroidering the structure? Thanks in advance for your reply!

what kind of trim is this? pvc? wood?

I was wondering if, when installing smartside 38, do I need to cut off the shiplaps at the corner butt joints?
It was kinda hard to tell on your previous video, but maybe I am over-thinking it. I checked LP Products website and downloaded their installation pdf, but there is no mention of it. I would think so, but would appreciate your thoughts

Perfection👍👍👍🎸☠️👍

very cool!

How much did the whole project costs?? And what's the size of the shed

where do you buy the materials....wall panels

What kinda lumber is used for the trim? I like that textured finish.

Not my proudest flap

This guys a pro spacer with those nails... not measuring and they look perfect as he's nailing them lol

shed rough
shed ruff

HELP ME please!!!. I purchased a 30L travel trailer. I am redoing the roof and found out everything has been framed with 2x2 pieces. My goal was to build a pitched gable above the RV so I could have a loft inside. I was going to be using 2x6 can anyone give me recommendations on if I'm able to use 2x4 or 2x6 as my rafter since the wall framing is only 2x2. Idk what to do please help

Hey i have a question, does it need to have a trim piece at the bottom of the shed? Like at the bottom edge of the shed all around it. Ive seem some bigger structures that have it and some that dont. Is it optional or what? Does water get in between the trim piece?

I'm building my kids treehouse and needed some pointers as I'm not a tradesman. Your videos are excellent - you show all the 'gotchas' and explain it with great videography and no bs that is found on so many other videos. Thanks so much. Subscribed!

I thought this was very well done, on my shed I am going to fit each piece then paint all sides and edges before installation to prevent rot . or at least slow it down.

Cool video! Did you use OSB for the fascia? is it 1/2 thick? Thank you.

Two questions. One, is the fascia board you used a composite wood or all wood? Two, what type of metal piece did you put between the siding on the gable ends?

This video series has been HUGE for me. Not sure I could have gotten as far as I have without these.

That shed and trim look like ass

where does he live, the mountains are beautiful here

Nice video series! What size/length nails did you use in the nail gun on the siding and trim?
Thanks for your time.
Ron

so nice

ah so you did butt joints instead of 45's

How do you reduce sugar in sugar?

Can you link a site where we can shop for that type of corner trim ?...thx.

Thanks for the help. Really appreciate it.

So how wide of a piece of trim are you cutting from that t11

What type of nails did you use?